Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TECHNOMELT PA 6238 known as MACROMELT 6238
- Product Code
- 78967
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Special hotmelt, based on polyamide
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Notes
Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.
Cool melted product on skin with plenty of water. Do not remove solidified product. No attempt should be made to remove material from skin or to remove contaminated clothing as damaged skin can be easily torn. Cover affected areas with clean sheeting or gauze and seek immediate medical attention.
Symptoms: Molten adhesive may cause severe burns.
If eye contact occurs with molten material immediately cool with water. Do not remove adhesive. Seek medical attention.
Symptoms: Molten adhesive may cause severe burns.
If symptoms develop and persist, get medical attention.
Immediate Medical Attention
Seek immediate medical attention for skin burns. Seek medical attention for eye contact or if symptoms persist.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide. Use extinguishing measures appropriate to local circumstances and the surrounding environment.
Not available.
Overexposure to decomposition products may cause a health hazard.
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow material to contaminate ground water system.
Sweep up spilled material and place in a closed container for disposal.
Related Products
Similar products with comparable safety profiles
TECHNOMELT PA 6239 known as MACROMELT 6239
---
TECHNOMELT PA 2192B known as MACROMELT 2192 B
---
TECHNOMELT PA 673 N known as MACROMELT OM 673
---
TECHNOMELT PA 653 known as MACROMELT OM 653
---
TECHNOMELT PA 682 known as MACROMELT 682 VZHHD001
---
TECHNOMELT PA 652 N known as MACROMELT OM 652 KG20
---
TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN
---
TECHNOMELT PA 2391 known as MACROMELT 2391 40LB
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid skin contact with molten resins. Do not place wet or damp solid into melt tank. Follow suggested application temperature. Do not wear contact lenses.
Keep container closed.
Do not wear contact lenses.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Local exhaust ventilation is recommended when general ventilation is not sufficient to control airborne contamination below occupational exposure limits.
Insulated gloves are strongly recommended when working with molten adhesive.
Wear safety glasses with side shields.
No personal respiratory protective equipment normally required. Where the potential exists for exposure to decomposition products due to heating or elevated temperatures, wear NIOSH approved respiratory protection as appropriate. Observe OSHA regulations for respirator use (29 CFR 1910.134).
Long sleeved clothing are strongly recommended when working with molten adhesive.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Normally stable.
Not available.
Will not occur.
Avoid strong oxidizing agents.
Reaction with strong oxidants.
Carbon dioxide, carbon monoxide and irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TECHNOMELT PA 6238 known as MACROMELT 6238?
The signal word is no signal word.
What is the physical form of TECHNOMELT PA 6238 known as MACROMELT 6238?
TECHNOMELT PA 6238 known as MACROMELT 6238 is a solid with amber color. It has characteristic odor.
What is the solubility of TECHNOMELT PA 6238 known as MACROMELT 6238?
Insoluble Water
What is TECHNOMELT PA 6238 known as MACROMELT 6238 used for?
Special hotmelt, based on polyamide
What are the hazard statements for TECHNOMELT PA 6238 known as MACROMELT 6238?
This substance has 3 hazard statements:
- MOLTEN ADHESIVE MAY CAUSE SEVERE BURNS.
- VAPORS ABOVE MOLTEN ADHESIVE MAY CAUSE EYE, SKIN AND RESPIRATORY TRACT IRRITATION.
- STATIC CHARGES GENERATED BY EMPTYING PACKAGE IN OR NEAR FLAMMABLE VAPORS MAY CAUSE IGNITION.
What is the melting point of TECHNOMELT PA 6238 known as MACROMELT 6238?
The melting point is 135 - 145 °C (275°F - 293°F) (Softening Point) and the boiling point is > 280 °C (> 536°F).