Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN
- Product Code
- 1334989
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Polyamide
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Bis(2-hydroxy-3-tert-butyl-5-methylphenyl)methane | 119-47-1 | 0.1 - 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.
Cool melted product on skin with plenty of water. Do not remove solidified product. No attempt should be made to remove material from skin or to remove contaminated clothing as damaged skin can be easily torn. Cover affected areas with clean sheeting or gauze and seek immediate medical attention.
Symptoms: Molten adhesive may cause severe burns.
If eye contact occurs with molten material immediately cool with water. Do not remove adhesive. Seek medical attention.
Ingestion of solid adhesive is not expected to be hazardous. If symptoms develop and persist, get medical attention.
Immediate Medical Attention
Seek immediate medical attention for skin contact. Seek medical attention if symptoms develop and persist for inhalation, eye contact, or ingestion.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide. Use extinguishing measures appropriate to local circumstances and the surrounding environment.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow material to contaminate ground water system.
Sweep up spilled material. Avoid creating dust. Keep in suitable and closed containers for disposal.
Materials: suitable and closed containers
Related Products
Similar products with comparable safety profiles
TECHNOMELT PA 2391 known as MACROMELT 2391 40LB
---
TECHNOMELT PA 6238 known as MACROMELT 6238
---
TECHNOMELT PA 652 N known as MACROMELT OM 652 KG20
---
TECHNOMELT PA 6239 known as MACROMELT 6239
---
TECHNOMELT PA 2302 BLACK known as MACROMELT 2302 S 20kg
---
TECHNOMELT PA 6300
---
TECHNOMELT PA 2192B known as MACROMELT 2192 B
---
TECHNOMELT PA 653 known as MACROMELT OM 653
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Always be careful around molten material. Avoid skin contact with molten resins. Do not place wet or damp solid into melt tank. Follow suggested application temperature. Do not wear contact lenses. At elevated temperatures, irritating fumes may be emitted.
Keep cool in accordance with information on label and in Technical Data Sheets.
Do not wear contact lenses.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Work should be done in an adequately ventilated area (i.e., ventilation sufficient to maintain concentrations below one half of the PEL and other relevant standards). Local exhaust ventilation is recommended when general ventilation is not sufficient to control airborne contamination.
Insulated gloves are strongly recommended when working with molten adhesive.
Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists. Do not wear contact lenses.
No personal respiratory protective equipment normally required. Where the potential exists for exposure to decomposition products due to heating or elevated temperatures, wear NIOSH approved respiratory protection as appropriate. Observe OSHA regulations for respirator use (29 CFR 1910.134).
Insulated gloves and long sleeved clothing are strongly recommended when working with molten adhesive.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable
Not available.
Will not occur.
Excessive heat.
Acids. Bases. Oxidizing agents.
Carbon dioxide, carbon monoxide and irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN?
The signal word is danger.
What is the physical form of TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN?
TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN is a solid with amber color. It has odourless / odorless odor.
What is the solubility of TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN?
Not soluble Water
What is TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN used for?
Polyamide
What are the hazard statements for TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN?
This substance has 1 hazard statement:
- H360: MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
What is the melting point of TECHNOMELT PA 6301 known as MACROMELT 6301 40LB EN?
The melting point is 95 - 105 °C (203°F - 221°F) and the boiling point is > 280.0 °C (> 536°F).