NextSDS Logo
Safety Data Sheet EN

LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82
Product Code
995529

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Material (PCTIM)

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

http://www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Skin Irrit. Cat. 2 H315
Eye Irrit. Cat. 2B H320

GHS Pictograms

GHS07 - Health hazard

GHS07

Hazard Statements

H315 + H320 CAUSES SKIN AND EYE IRRITATION

Precautionary Statements

P264 Wash affected area thoroughly after handling.
P280 Wear protective gloves.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P332 + P313 If skin irritation occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

3. COMPOSITION / INFORMATION ON INGREDIENTS

Chemical Name CAS Number Concentration Hazardous
Paraffin waxes and Hydrocarbon waxes 8002-74-2 10 - 30% Yes
Zinc oxide 1314-13-2 5 - 10% Yes
Petrolatum 8009-03-8 1 - 5% Yes

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.

Skin contact

Remove contaminated clothing and footwear. Immediately flush skin with plenty of water (using soap, if available). If symptoms develop and persist, get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Seek medical attention immediately.

Ingestion

DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. If symptoms develop and persist, get medical attention.

Immediate Medical Attention

Seek medical attention immediately for eye contact. If symptoms develop and persist for other exposure routes, get medical attention.

Medical Treatment

Treat symptomatically and supportively.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

In case of fire, keep containers cool with water spray.

Instructions

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. Keep unnecessary personnel away. In case of fire, keep containers cool with water spray.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel. Refer to Section 8 'Exposure Controls / Personal Protection' prior to clean up.

Small spill

If product is spilled in the solid state, pick up and place in an appropriate waste disposal container. If product is spilled in the molten state, allow product to solidify before scraping up and disposing of in an appropriate waste disposal container.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

If product is spilled in the solid state, pick up and place in an appropriate waste disposal container. If product is spilled in the molten state, allow product to solidify before scraping up and disposing of in an appropriate waste disposal container.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Do not taste or swallow. Avoid breathing vapors or mists of this product. Keep container closed.

Storage

Store at or below 40 °C (104°F). Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.

Hygiene

When using do not eat, drink or smoke. Wash thoroughly after handling.

Fire prevention

Keep in a cool, well ventilated area away from heat, sparks and open flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Voc Content
0 %
Density
---
Upper Explosive Limit
Not available.
Physical State
Solid, (coated polyimide film)
Solidification Point
---
Explosive Limits
---
Flash Point
221 °C (429.8 °F) Cleveland open cup
Vapor Pressure
< 1 hPa (20 °C (68°F))
Boiling Point
> 200 °C (> 392°F)
Lower Explosive Limit
Not available.
Physical State Data
solid
Evaporation Rate
Not available.
Relative Density
1.4
Colour
White, Tan
Relative Evaporation Rate
---
Kinematic Viscosity
Not available.
Melting Point
60 °C (140°F) Decomposes., 60 °C (140°F) (coating compound), 650 °C (1,202°F) (polyimide film)
Metal Corrosion
---
Vapor Density
---
Cloud Point
---
Dynamic Viscosity
Not available.
Decomposition Temperature
Not available.
Molecular Weight
---
Freezing Point
---
Odor Threshold
Not available.
Crystallisation Point
---
Ph
Not applicable, Product is non-soluble (in water).
Auto Ignition Temperature
Not available.
Appearance
---
Solubility In Water
Insoluble
Colour Intensity
---
Solubility In Fat
---
Properties Status
---
Solubility
Insoluble Water
Bulk Density
---
Flammability
The product is not flammable.
Form
---
State Under Standard Conditions
---
Partition Coefficient
Not available.
Odor
---
Softening Point
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Heat, flames, sparks and other sources of ignition. Store away from incompatible materials.

Incompatible

Strong acids, alkalies and oxidizing agents. Halogenated compounds.

Decomposition

Oxides of carbon. Oxides of nitrogen. Hydrocarbons.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3077
Shipping Name
Environmentally hazardous substance, solid, n.o.s. (Zinc oxide)
Transport Class
9
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82?

The signal word is warning.

What is the physical form of LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82?

LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82 is a solid, (coated polyimide film) with white, tan color.

What is the solubility of LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82?

Insoluble Water

What is LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82 used for?

Material (PCTIM)

What are the hazard statements for LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82?

This substance has 1 hazard statement:

  • H315 + H320: CAUSES SKIN AND EYE IRRITATION

What is the melting point of LOCTITE EIF 1000 K3 known as Isostrate 6.12 X 0.82?

The melting point is 60 °C (140°F) Decomposes., 60 °C (140°F) (coating compound), 650 °C (1,202°F) (polyimide film) and the boiling point is > 200 °C (> 392°F).