Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE EIF 1000K3 known as K3-076-059
- Product Code
- 2262634
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Phase Change Thermal Interface Material (PCTIM)
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Paraffin waxes and Hydrocarbon waxes | 8002-74-2 | 10 - 30% | Yes |
| Zinc oxide | 1314-13-2 | 5 - 10% | Yes |
| Petrolatum | 8009-03-8 | 1 - 5% | Yes |
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration.
Remove contaminated clothing and footwear. Immediately flush skin with plenty of water (using soap, if available). Wash clothing before reuse. Thoroughly clean shoes before reuse.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.
DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Seek medical attention immediately (for eye contact). If symptoms develop and persist, get medical attention (for inhalation, skin contact, and ingestion).
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
In case of fire, keep containers cool with water spray.
Keep unnecessary personnel away. In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean up.
If product is spilled in the solid state, pick up and place in an appropriate waste disposal container.
If product is spilled in the molten state, allow product to solidify before scraping up and disposing of in an appropriate waste disposal container.
Do not allow product to enter sewer or waterways.
If product is spilled in the solid state, pick up and place in an appropriate waste disposal container. If product is spilled in the molten state, allow product to solidify before scraping up and disposing of in an appropriate waste disposal container.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes, skin and clothing. Do not taste or swallow. Avoid breathing vapors or mists of this product. Keep container closed.
Store at or below 40 °C. Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.
When using do not eat, drink or smoke. Wash thoroughly after handling.
Keep away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
None under normal processing.
Heat, flames, sparks and other sources of ignition. Store away from incompatible materials.
Strong acids, alkalies and oxidizing agents. Halogenated compounds.
Oxides of carbon. Oxides of nitrogen. Hydrocarbons.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3077
- Shipping Name
- Environmentally hazardous substance, solid, n.o.s. (Zinc oxide)
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE EIF 1000K3 known as K3-076-059?
The signal word is warning.
What is the physical form of LOCTITE EIF 1000K3 known as K3-076-059?
LOCTITE EIF 1000K3 known as K3-076-059 is a solid, (coated polyimide film) with white, tan color.
What is the solubility of LOCTITE EIF 1000K3 known as K3-076-059?
Insoluble Water
What is LOCTITE EIF 1000K3 known as K3-076-059 used for?
Phase Change Thermal Interface Material (PCTIM)
What are the hazard statements for LOCTITE EIF 1000K3 known as K3-076-059?
This substance has 1 hazard statement:
- H315 + H320: CAUSES SKIN AND EYE IRRITATION.
What is the melting point of LOCTITE EIF 1000K3 known as K3-076-059?
The melting point is 60 °C (140°F) Decomposes.; 60 °C (140°F) (coating compound); 650 °C (1,202°F) (polyimide film) and the boiling point is > 200 °C (> 392°F).