Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- AAG Rubber Seal 320
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
No special
Uses advised against
No special
Manufacturers & Suppliers
Aalborg Gummivarefabrik AS
manufacturer
Sundsholmen 3, DK-9400 Nørresundby, Denmark
Emergency Contacts
The National Poisons Information Service
111
24 h service
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Trimethoxyvinylsilane EC: 220-449-8 | 2768-02-7 | 1% | Yes |
| 2-methoxy-1-methylethyl acetate EC: 203-603-9 | 108-65-6 | 0.05% | Yes |
| bis(1,2,2,6,6-pentamethyl-4-piperidyl) [(3,5-bis(1,1-dimethylethyl)... EC: 264-513-3 | 63843-89-0 | 0.05% | Yes |
| Methanol (released in small quantities during vulcanisation) EC: 200-659-6 | 67-56-1 | 0.0015% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Upon breathing difficulties or irritation of the respiratory tract: Bring the person into fresh air and stay with him/her.
IF ON SKIN: Wash with plenty of water and soap. Remove contaminated clothing and shoes. Ensure to wash exposed skin thoroughly with water and soap. DO NOT use solvents or thinners. If skin irritation occurs: Get medical advice/attention.
Symptoms: Skin irritation
Upon irritation of the eye: Remove contact lenses and open eyes widely. Flush eyes with water or saline water(20-30°C) for at least 5 minutes. Seek medical assistance and continue flushing during transport.
Symptoms: Irritation of the eye
Provide plenty of water for the person to drink and stay with him/her. In case of malaise, seek medical advice immediately and bring the safety data sheet or label from the product. Do not induce vomiting, unless recommended by the doctor. Have the victim lean forward with head down to avoid inhalation of- or choking on vomited material.
Symptoms: Malaise
Immediate Medical Attention
Contact a doctor or casualty department – take the label or this safety data sheet. Contact a doctor if in doubt about the injured person's condition or if the symptoms persist. Seek medical assistance and continue flushing during transport (for eye contact). In case of malaise, seek medical advice immediately.
Medical Treatment
Bring this safety data sheet or the label from this product.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Alcohol-resistant foam, carbon dioxide, powder, water mist.
Waterjets should not be used, since they can spread the fire.
Fire will result in dense smoke. Exposure to combustion products may harm your health. Closed containers, which are exposed to fire, should be cooled with water.
Closed containers, which are exposed to fire, should be cooled with water.
Firefighter Protection
Fire fighters should wear appropriate personal protective equipment.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
No specific requirements
Avoid discharge to lakes, streams, sewers, etc.
To the extent possible cleaning is performed with normal cleaning agents. Avoid use of solvents.
Related Products
Similar products with comparable safety profiles
Gutter & Flashing Butyl-Flex Rubber Sealant
---
Gasketseal
---
DAP 100% Silicone Rubber Sealant Almond
---
UV SEALER 661-103-0000
---
UV SEALER 661-X-107-005
---
MasterSeal® M 276 Part A
---
205815 Floor Seal
UFI: 44MC-WP7M-NN65-Q9FT
Touch N Seal Foam Kit 300 1.0 PCF Low GWP A Side
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Smoking, drinking and consumption of food is not allowed in the work area.
No specific requirements
Smoking, drinking and consumption of food is not allowed in the work area.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The formation of vapours must be kept at a minimum and below current limit values (see above). Installation of a local exhaust system if normal air flow in the work room is not sufficient is recommended. Ensure emergency eyewash and -showers are clearly marked.
When applying the sealant with a caulking gun and when finishing: Nitrile. With a joint nail, work can be carried out without gloves if skin contact is avoided. When applying the glue with a glue gun or tube work can be carried out without gloves if skin contact is avoided.
No specific requirements
If used in small and very badly ventilated rooms (not relevant if the room is well ventilated): Type AX, Colour Brown, Standards EN14387
Dedicated work clothing should be worn.
No specific requirements
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable under the conditions, noted in section 7 "Handling and storage".
No data available
No special
No special
Strong acids, strong bases, strong oxidizing agents, and strong reducing agents.
The product is not degraded when used as specified in section 1.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for AAG Rubber Seal 320?
The signal word is no signal word.
What is the physical form of AAG Rubber Seal 320?
AAG Rubber Seal 320 is a paste with according to specification color. It has faint odor.
What is AAG Rubber Seal 320 used for?
No special
What is the melting point of AAG Rubber Seal 320?
The melting point is Testing not relevant or not possible due to nature of the product. and the boiling point is Testing not relevant or not possible due to nature of the product..