NextSDS Logo
Safety Data Sheet EN

AS-90

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
AS-90
Product Form
Aerosol
Product Code
UDS000734AE

Regulatory Identifiers

CAS Number
N/A
UFI Code
SYDY-08V1-W00J-87QY

Identified Uses

Professional use; Welding and soldering agents

Uses advised against

Consumer uses: Private households (= general public = consumers)

Manufacturers & Suppliers

CRC Industries Europe UK Limited logo

CRC Industries Europe UK Limited

distributor

Wylds Road, Castlefield Industrial Estate, TA6 4DD Bridgewater Somerset, United Kingdom

+44 1278 727200

http://www.crcind.com

CRC Industries Europe B.V. logo

CRC Industries Europe B.V.

Touwslagerstraat 1, 9240 Zele, Belgium

+32(0)52/45.60.11

http://www.crcind.com

Emergency Contacts

Centre Anti-Poisons/Antigifcentrum c/o Hôpital Militaire Reine Astrid

+32 70 245 245

24/7

Centre Anti-Poisons/Antigifcentrum c/o Hôpital Militaire Reine Astrid

02 264 96 30

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Aerosol Cat. 3 H229
Skin Irrit. Cat. 2 H315
Eye Irrit. Cat. 2 H319
Carc. Cat. 2 H351
STOT SE Cat. 3 H336

GHS Pictograms

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H229 Pressurised container: May burst if heated.
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.
H351 Suspected of causing cancer.

Precautionary Statements

P102 Keep out of reach of children.
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P251 Do not pierce or burn, even after use.
P260 Do not breathe mist/vapours.
P280 Wear protective gloves/eye protection.
P308 + P313 IF exposed or concerned: Get medical advice/attention.
P410 + P412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C.
P501 Dispose of contents/container to a hazardous or special waste collection point, in accordance with local, regional, national and/or international regulation.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
dichloromethane; methylene chloride EC: 200-838-9 75-09-2 75 - 100% Yes
Carbon dioxide (CO2) (Propellant gas (Aerosol)) 124-38-9 1 - 5% Yes
Mineral oil --- 1 - 5% Yes

Product subject to CLP Annex I, item 1.1.3.7. The disclosure rules of the components is modified in this case.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person to fresh air and keep comfortable for breathing. If signs/symptoms develop, get medical attention.

Symptoms: None under normal conditions.

Skin contact

Wash skin with plenty of water. Take off contaminated clothing. If skin irritation occurs: Get medical advice/attention. Seek medical attention if irritation develops.

Symptoms: Irritation. Repeated exposure may cause skin dryness or cracking.

Eye contact

Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. Seek medical attention if irritation develops.

Symptoms: Eye irritation.

Ingestion

Call a poison center or a doctor if you feel unwell.

Immediate Medical Attention

If signs/symptoms develop, get medical attention.

Medical Treatment

Provide general supportive measures and treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray. Dry powder. Foam. Carbon dioxide.

Unsuitable media

Do not use a heavy water stream.

Specific hazards

Pressurised container: May burst if heated.

Instructions

Move containers from fire area if it can be done without personal risk. Use standard firefighting procedures and consider the hazards of other involved materials.

Firefighter Protection

Do not attempt to take action without suitable protective equipment. Self-contained breathing apparatus. Complete protective clothing.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Ventilate spillage area. No open flames, no sparks, and no smoking. Avoid breathing dust/fume/gas/mist/vapours/spray. Avoid contact with skin and eyes. Evacuate unnecessary personnel.

Small spill

Take up small spills with dry chemical absorbent

Large spill

confine the spill in a dike and charge it with wet sand or earth for subsequent safe disposal

Environmental

Avoid release to the environment.

Cleanup methods

Mechanically recover the product. Following product recovery, flush area with water. Clean surface thoroughly to remove residual contamination.

Materials: dry chemical absorbent

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear personal protective equipment. Use only outdoors or in a well-ventilated area. Avoid breathing dust/fume/gas/mist/vapours/spray. Avoid contact with skin and eyes. Avoid prolonged exposure. Handle in accordance with good industrial hygiene and safety procedures.

Storage

Protect from sunlight. Do not expose to temperatures exceeding 50 °C/ 122 °F. Store locked up. Store in a well-ventilated place. Keep container tightly closed. Keep cool. Keep container closed when not in use.

Hygiene

Wash contaminated clothing before reuse. Do not eat, drink or smoke when using this product. Always wash hands after handling the product.

Fire prevention

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Good general ventilation should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.

Hands

Wear suitable gloves tested to EN374. The breakthrough time of the glove should be longer than the total duration of product use. If work lasts longer than the breakthrough time, gloves should be changed part-way through. Polyvinylalcohol (PVA).

Eyes

Use eye protection according to EN 166. Safety glasses with side shields.

Respiratory

In case of insufficient ventilation, wear suitable respiratory equipment. Approved organic vapour respirator. Filter type: AX

Skin/Body

Wear suitable protective clothing

Environmental

Avoid release to the environment. Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Properties Status
---
Dynamic Viscosity
---
Odor Threshold
Not available
Solidification Point
---
Vapor Pressure
Not available
Softening Point
---
Solubility In Water
---
Explosive Limits
---
Kinematic Viscosity
Not available
Vapor Density
---
Solubility
Insoluble in water.
Relative Evaporation Rate
---
Freezing Point
Not available
Lower Explosive Limit
Not available
Metal Corrosion
---
Physical State
Liquid
Odor
characteristic.
Molecular Weight
---
Form
---
Flammability
Non flammable.
Colour
Yellow.
Cloud Point
---
Solubility In Fat
---
Physical State Data
aerosol
Auto Ignition Temperature
Not available
Melting Point
No data available
Decomposition Temperature
Not available
Voc Content
---
Evaporation Rate
---
Partition Coefficient
Not applicable
Ph
Not applicable
Colour Intensity
---
Flash Point
Not applicable
Crystallisation Point
---
Appearance
CO2 propelled liquid.
State Under Standard Conditions
---
Bulk Density
---
Density
1,295 g/cm³ at 20 °C
Relative Density
1,295 at 20 °C
Boiling Point
Not available
Upper Explosive Limit
Not available
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions.

Reactivity

Pressurised container: May burst if heated.

Hazardous reactions

No dangerous reactions known under normal conditions of use.

Avoid

Avoid contact with hot surfaces. Heat. No flames, no sparks. Eliminate all sources of ignition.

Incompatible

Strong oxidizing agents.

Decomposition

Under normal conditions of storage and use, hazardous decomposition products should not be produced. Carbon oxides (CO, CO2).

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1950
Shipping Name
AEROSOLS
Transport Class
2.2
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for AS-90?

The signal word is warning.

What is the physical form of AS-90?

AS-90 is a liquid appearing as co2 propelled liquid. with yellow. color. It has characteristic. odor.

What is the solubility of AS-90?

Insoluble in water.

What is AS-90 used for?

Professional use; Welding and soldering agents

What are the hazard statements for AS-90?

This substance has 5 hazard statements:

  • H229: Pressurised container: May burst if heated.
  • H315: Causes skin irritation.
  • H319: Causes serious eye irritation.
  • H336: May cause drowsiness or dizziness.
  • H351: Suspected of causing cancer.

What is the melting point of AS-90?

The melting point is No data available and the boiling point is Not available.