Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- FW Anilox + Cleaner
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cleaner for solvent based-/UV and water based inks.
Uses advised against
The full text of any mentioned and identified use categories are given in section 16
Manufacturers & Suppliers
Flexo Wash ApS
manufacturer
Grenåvej 631 K, DK - 8541 Skødstrup
+45 86 99 36 31
http://www.flexowash.com
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| (2-methoxymethylethoxy)propanol EC: 252-104-2 | 34590-94-8 | 10 - 15% | No |
| Tetrasodium ethylene diamine tetraacetate EC: 200-573-9 | 64-02-8 | 3 - 5% | Yes |
| Sodium hydroxide caustic soda EC: 215-185-5 | 1310-73-2 | 1 - 3% | Yes |
| Alcohol C9-11, ethoxylated EC: 500-446-0 | 68439-46-3 | 1 - 3% | Yes |
| Fatty alcohol alkoxylate | --- | 1 - 3% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Bring the injured person into fresh air. Make sure the injured person is continuously monitored. Prevent shock by keeping the injured person warm and calm. If breathing ceases, give mouth-to-mouth resuscitation. If unconscious, roll the injured person into recovery position. Call an ambulance.
Symptoms: Inhaled vapour or aerosols may produce adverse effects to lungs, irritations and burns in the respiratory organs, as well as coughing. Irritation to lungs.
Remove contaminated clothing and shoes immediately. Ensure to wash exposed skin thoroughly with water and soap. Skin cleanser can be used. For burns: Rinse with water until the pain stops and continue for 30 minutes.
Symptoms: Skin corrosive properties. Dermal contact causes irreversible effects. Tingling sensations of skin. Irritation to skin.
Remove contact lenses. Flush eyes with plenty of water or salt water (20-30°C) for at least 15 minutes and continue until irritation stops. Make sure you flush under the upper and lower eyelids. Seek medical assistance immediately and continue flushing.
Symptoms: Contact with the eye causes irreversible effects. Irritation to eyes.
Provide plenty of water for the person to drink and stay with him/her. In case of malaise, seek medical advice immediately and bring the safety data sheet or label from the product. Do not induce vomiting, unless recommended by the doctor. Have the victim lean forward with head down to avoid inhalation of- or choking on vomited material.
Symptoms: malaise
Immediate Medical Attention
Seek medical assistance immediately for eye contact or in case of malaise.
Medical Treatment
Bring this safety data sheet.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
alcohol-resistant foam, carbonic acid, powder, water mist
Waterjets should not be used, since they can spread the fire.
Fire will result in dense black smoke. Exposure to combustion products may harm your health.
Upon direct exposure contact The National Poisons Information Service (dial 111, 24 h service) in order to obtain further advice.
Firefighter Protection
Fire fighters should wear appropriate protection equipment.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid direct contact with spilled substances. Avoid inhalation of vapours from spilled material.
No specific requirements.
To the extent possible cleaning is performed with normal cleaning agents. Avoid use of solvents.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Smoking, storage of tobacco, consumption and storage of food or liquids are not allowed in the workrooms. Avoid direct contact with the product.
Always store in containers of the same material as the original container. Containers that have been opened must be carefully resealed and kept upright to prevent leakage.
Smoking, storage of tobacco, consumption and storage of food or liquids are not allowed in the workrooms.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Airborne gas and dust concentrations must be kept at a minimum and below current limit values (see above). Installation of an exhaust system if normal air flow in the work room is not sufficient is recommended. Ensure emergency eyewash and -showers are clearly marked.
Recommended: Nitrile rubber. Breakthrough time: > 480 minutes (Class 6)
Wear safety glasses with side shields.
Recommended: A. Class 2 (medium capacity). Brown
Wear appropriate protection clothing, e.g. coveralls in polypropylene approved type 6 and Category III.
Keep damming materials near the workplace. If possible, collect spillage during work.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable under the conditions, noted in the section "Handling and storage".
No data available
No special
Do not expose to any forms of heat (e.g. solar radiation). May lead to excess pressure.
Strong acids, strong bases, strong oxidizing agents, and strong reducing agents.
The product is not degraded when used as specified in section 1.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1719
- Shipping Name
- CAUSTIC ALKALI LIQUID, N.O.S. (sodium hydroxide)
- Transport Class
- 8
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for FW Anilox + Cleaner?
The signal word is danger.
What is the physical form of FW Anilox + Cleaner?
FW Anilox + Cleaner is a liquid appearing as no data available. with no data available. color. It has characteristic odor.
What is FW Anilox + Cleaner used for?
Cleaner for solvent based-/UV and water based inks.
What are the hazard statements for FW Anilox + Cleaner?
This substance has 1 hazard statement:
- H314: Causes severe skin burns and eye damage.
What is the melting point of FW Anilox + Cleaner?
The melting point is No data available. and the boiling point is No data available..