Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Tin(II) chloride dihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur
- Product Code
- 107815
- Chemical Name
- Tin(II) chloride dihydrate
Regulatory Identifiers
- CAS Number
- 10025-69-1 Check regulations →
- REACH No.
- 01-2119971277-28-XXXX
Identified Uses
Reagent for analysis
Manufacturers & Suppliers
Merck Life Science BV/SRL
distributor
Brusselsesteenweg 288, B-3090 OVERIJSE
+32 (0)3 899-1301
Emergency Contacts
CHEMTREC
+(32) 28 083237
Anti-poison centre
070 245245
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Stannous chloride dihydrate EC: 231-868-0 | 10025-69-1 | 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air. Immediately call in physician. If breathing stops: immediately apply artificial respiration, if necessary also oxygen.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Call a physician immediately.
After eye contact: rinse out with plenty of water. Immediately call in ophthalmologist. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most), avoid vomiting (risk of perforation). Call a physician immediately.
Immediate Medical Attention
Call a physician immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
For this substance/mixture no limitations of extinguishing agents are given.
Hydrogen chloride gas, Tin/tin oxides. Not combustible. Fire may cause evolution of: Hydrogen chloride gas. Ambient fire may liberate hazardous vapours.
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Firefighter Protection
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up dry. Clean up affected area.
Related Products
Similar products with comparable safety profiles
Tin(II) chloride dihydrate for analysis (max. 0.000001% Hg) EMSURE®
---
Iron(III) chloride hexahydrate for analysis EMSURE® ACS, Reag. Ph Eur
CAS: 10025-77-1
Iron(III) chloride hexahydrate for analysis EMSURE® ACS, Reag. Ph Eur
CAS: 10025-77-1
Calcium chloride dihydrate for analysis EMSURE® ACS, Reag. Ph Eur
CAS: 10035-04-8
Mercury(II) chloride for analysis EMSURE® Reag. Ph Eur,ACS
CAS: 7487-94-7
Sodium chloride for analysis EMSURE® ACS,ISO,Reag. Ph Eur
CAS: 7647-14-5
Sodium chloride for analysis EMSURE® ACS,ISO,Reag. Ph Eur
CAS: 7647-14-5
Ammonium chloride for analysis EMSURE® ACS,ISO,Reag. Ph Eur
CAS: 12125-02-9
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Work under hood. Do not inhale substance/mixture.
Tightly closed. Dry. Recommended storage temperature see product label.
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L.
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Tightly fitting safety goggles
required when dusts are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type P2
protective clothing
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
No data available
Violent reactions possible with: Strong acids, hydrogen peroxide. Risk of ignition or formation of inflammable gases or vapours with: halogen-halogen compounds, Ethylene oxide, carbides. Risk of explosion with: hydrazine and derivatives, nitrates, Alkali metals, Strong oxidizing agents.
Exposure to moisture may affect product quality. Exposure to air may affect product quality.
No data available
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3260
- Shipping Name
- CORROSIVE SOLID, ACIDIC, INORGANIC, N.O.S. (Stannous chloride dihydrate)
- Transport Class
- 8
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Tin(II) chloride dihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur?
The signal word is danger.
What is the physical form of Tin(II) chloride dihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur?
Tin(II) chloride dihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur is a solid with white color. It has odorless odor.
What is Tin(II) chloride dihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur used for?
Reagent for analysis
What are the hazard statements for Tin(II) chloride dihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur?
This substance has 7 hazard statements:
- H290: May be corrosive to metals.
- H302 + H332: Harmful if swallowed or if inhaled.
- H314: Causes severe skin burns and eye damage.
- H317: May cause an allergic skin reaction.
- H335: May cause respiratory irritation.
- H373: May cause damage to organs (Cardio-vascular system) through prolonged or repeated exposure if swallowed.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of Tin(II) chloride dihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur?
The melting point is 38 °C and the boiling point is No data available.