POLISH KP92 – Polishing Powder

Bring the subject outdoors. If breathing is difficult, seek medical attention.

Wash immediately with plenty of running water and possibly with soap areas of the body that have come in contact with the product, even if only suspected. Wash thoroughly the body (shower or bath). Remove contaminated clothing immediately and dispose of safely.

Remove any contact lenses. Wash immediately with plenty of water for at least 15 minutes, opening her eyelids. Consult a doctor if the problem persists.

Call a doctor immediately. Induce vomiting only if indicated by the doctor. Never give anything by mouth to an unconscious person unless authorized by your doctor. Show this safety data sheet.

carbon dioxide, foam, powder and nebulised water.

No one in particular.

HAZARDS CAUSED BY EXPOSURE IN CASE OF FIRE. Do not breathe combustion products. ACID SALTS OXALIC: To combustion can form caustic potassium oxide fumes.

Cool down with water jets the containers to prevent product decomposition and the development of substances potentially hazardous for health. Collect extinguishing water which must not be discharged into drains. Dispose of contaminated water used for extinction and the remains according to current regulations.

Avoid breathing vapors / mist / gas.

Contain waste with earth or sand. If you contaminate a water course, a sewer or has contaminated soil or vegetation, consult the competent authority network.

Collect mechanically spark leaked product and add it to containers for recovery or disposal.

Handle the product after consultation with all other sections of this SDS. Avoid dispersal into the environment. Do not eat, drink or smoke while handling it. Remove contaminated clothing and protective equipment before entering areas in which you eat.

Store only in the original container. Store closed containers in well-ventilated place, away from direct sunlight.

Do not eat, drink or smoke while handling it. Remove contaminated clothing and protective equipment before entering areas in which you eat.

Given that the use of appropriate technical measures should always take priority over personal protection equipment, ensure good ventilation in the workplace through effective local aspiration.

In case there is a prolonged contact with the product, it is advisable to protect your hands with work gloves resistant to penetration (ref. Standard EN 374). Recommended a thickness of gloves> 0.11 mm NBR (Nitrile rubber) or Neoprene. Final selection of the material of the gloves must also evaluate the process of using the product and any other products derived from them. It also recalled that the latex gloves can lead to sensitization.

It is advisable to wear protective airtight goggles (ref. Standard EN 166). If there is the risk of being exposed to splashes or squirts during work, provision should be made adequate protection of the mucous membranes (mouth, nose, eyes) in order to prevent accidental absorption.

In case of exceeding the threshold value of one or more of the substances present in the preparation reported to the daily exposure to work environment or to a fraction established by the service of prevention and corporate security, wear a facial filter type FFP3 (ref. standard EN 141). The use of respiratory protection means, such as masks with cartridges for organic vapor and dust / mist, it is necessary in the absence of technical measures to limit the exposure of the worker. The protection provided by masks is in any case limited. In the case in which the substance in question is odorless or its olfactory threshold is higher than the relative exposure and in case of emergency limit, ie, when exposure levels are unknown or the concentration of oxygen in the workplace is less than 17% volume, wear a compressed air breathing apparatus open circuit (ref. standard EN 137) or respirator outside air inlet for use with full face mask, half mask or mouthpiece (ref. standard EN 138).

Wear work clothing with long sleeves and safety footwear for professional use Category II (ref. Directive 89/686 / EEC and standard EN ISO 20344). Wash with soap and water after removing protective clothing.

The emissions from production processes, including those from ventilation should be checked for compliance with the environmental protection legislation.

The product is stable under normal conditions of use and storage.

There are no particular risks of reaction with other substances in normal conditions of use. Saturated aqueous solutions (15%) behave as mediumstrong acids.

Oxalic acid generates explosive reaction mixtures with various oxidizing agents. It reacts violently developing heat with alkali metals, ammonia, mercury, furfuryl acid, chlorates and hypochlorites. Risk of explosion on contact with: silver and sodium chlorite.

temperatures above 157 ° C

Strong oxidizing agents. Metals and alkali metals, furfuryl acid and some of the chlorine compounds.

Oxalic acid carbon oxides

In the case of acid or basic product, at first always neutralize the product.

Disposal must be performed through an authorized waste management, in compliance with national and local regulations.