Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Remint Polishing Compound H
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Polishing agent
Uses advised against
None known.
Manufacturers & Suppliers
Mirka Ltd
manufacturer
Pensalavägen 210, 66850 Jeppo / FINLAND
http://www.mirka.com
Emergency Contacts
Mirka Ltd
+358 20 760 2111
8:00 - 16:00
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Cerium dioxide EC: 215-150-4 | 1306-38-3 | 10 - 30% | No |
| Lanthanum oxide EC: 215-200-5 | 1312-81-8 | 10 - 20% | No |
| 1,2-benzisothiazol-3(2H)-one EC: 220-120-9 | 2634-33-5 | 0.005 - 0.05% | No |
Notes
Substances of Very High Concern - SVHC: substances are not contained or are below 0.1%.
First Aid Measures
Emergency procedures for chemical exposure incidents
Ensure supply of fresh air. In the event of symptoms seek medical treatment.
When in contact with the skin, clean with soap and water. Consult a doctor if skin irritation persists.
Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Get medical advice. Do not induce vomiting. Rinse out mouth and give plenty of water to drink.
Immediate Medical Attention
In the event of symptoms seek medical treatment. If eye irritation persists: Get medical advice/attention. Consult a doctor if skin irritation persists. Get medical advice.
Medical Treatment
Treat symptomatically. Forward this sheet to the doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Product itself is non-combustible. Fire extinguishing method of surrounding areas must be considered.
Full water jet.
Risk of formation of toxic pyrolysis products.
Firefighter Protection
Use self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Ensure adequate ventilation.
Prevent spread over a wide area (e.g. by containment or oil barriers).
Take up with absorbent material (e.g. general-purpose binder).
Materials: absorbent material (e.g. general-purpose binder)
Related Products
Similar products with comparable safety profiles
Metal Polish
UFI: SJPV-J00T-A000-Q6FM
Polarshine E3 Glass Polishing Compound
---
GLASS POLISHING COMPOUND POLISHING SOLUTION
---
3M™ Finesse-It™ Polish - Final Finish
---
FARECLA G10 FINISHING COMPOUND
---
Motip 2K Clear coat highgloss
---
MasterFinish RL 211 also RHEOFINISH 211
---
POLYMER REMOVER
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only in well-ventilated areas. Avoid spilling in enclosed areas. Avoid contact with eyes and skin. Use personal protective equipment. Do not eat, drink or smoke when using this product. Wash hands before breaks and after work. Use barrier skin cream. Take off contaminated clothing and wash before reuse.
Keep only in original container. Keep container tightly closed.
Do not eat, drink or smoke when using this product. Wash hands before breaks and after work. Use barrier skin cream. Take off contaminated clothing and wash before reuse.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation on workstation. Measurement methods for taking workplace measurements must meet the performance requirements of DIN EN 482. For example, recommendations are given in the IFA's list of hazardous substances.
> 0,11 mm, Butyl rubber, >480 min (EN 374-1/-2/-3). The details concerned are recommendations. Please contact the glove supplier for further information.
Safety glasses. (EN 166:2001)
In the event of occupational exposure limits being exceeded or of inadequate ventilation: wear appropriate respiratory protection. short term: filter apparatus, filter P1 (DIN EN 143)
Protective clothing (EN 340)
Comply with applicable environmental regulations limiting discharge to air, water and soil.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal ambient conditions (ambient temperature).
No dangerous reactions known if used as directed.
No hazardous reactions known.
No information available.
No information available.
No dangerous reactions known if used as directed.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
It is not possible to determine a waste code for this product in accordance with the European Waste Catalogue (EWC) since it is only possible to classify it according to how it is used by the customer. The waste code is to be determined within the EU in liaison with the waste-disposal operator.
Dispose of as hazardous waste. Coordinate disposal with the authorities if necessary.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- Shipping Name
- Not classified as dangerous goods
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Remint Polishing Compound H?
The signal word is no signal word.
What is the physical form of Remint Polishing Compound H?
Remint Polishing Compound H is a liquid with red-brown color. It has odourless odor.
What is Remint Polishing Compound H used for?
Polishing agent
What is the melting point of Remint Polishing Compound H?
The melting point is No information available. and the boiling point is No information available..