ALEXIT-Verdünner / Thinner S 66

Remove to fresh air, keep patient warm and at rest. Irregular breathing/no breathing: artificial respiration. If unconscious place in recovery position and seek medical advice.

Take off all contaminated clothing immediately. Wash skin thoroughly with soap and water or use recognised skin cleanser. Do NOT use solvents or thinners!

Remove contact lenses, irrigate copiously with clean, fresh water for at least 10 minutes, holding the eyelids apart and seek medical advice.

Do NOT induce vomiting. If accidentally swallowed obtain immediate medical attention. Never give anything by mouth to an unconscious person. Keep at rest.

Alcohol resistant foam, CO2, powders, water spray

High volume water jet

Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard.

Cool endangered containers with water in case of fire.

Do not inhale vapours. Refer to protective measures listed in sections 7 and 8.

Do not let product enter drains. If the product contaminates lakes, rivers or sewage, inform appropriate authorities in accordance with local regulations.

Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous earth and place in container for disposal according to local regulations (see chapter 13). Clean preferably with a detergent; avoid use of solvents.

Materials: non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous earth

Prevent the creation of flammable or explosive concentrations of vapour in air and avoid vapour concentrations higher than the occupational exposure limits. Comply with the health and safety at work laws. Smoking, eating and drinking should be prohibited in the application area. Observe specific national regulations for handling and use of paints.

Keep container dry in a cool, well-ventilated place. Avoid heating and direct sunlight. Keep in containers of same material as the original one.

Smoking, eating and drinking should be prohibited in the application area.

The product should only be used in areas from which all naked lights and other sources of ignition have been excluded. Preparation may charge electrostatically: always use earthing leads when transferring from one container to another. Operators should wear anti-static footwear and clothing. No sparking tools should be used.

Provide adequate ventilation. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction. If these are not sufficient to maintain aerosol- and solvent vapours concentration below the OEL, suitable respiratory protection must be worn.

Adhere to the professional organisation rule "Use of protective gloves". Appropriate chemicals resistant glove tested in compliance with EN 374. Recommendation for protection against components generally found in the products: For short-term contact (i.e. splash protection): Appropriate material: nitrile rubber, Neoprene. Material thickness: > 0,4 mm. Breakthrough time: > 480 min. Before use, the protective glove should be tested in any case for its specific work-station suitability (i.e. mechanical resistance, product compatibility and antistatic properties). Adhere to the manufacturer's instructions and information relating to the use, storage, care and replacement of protective gloves. Protective gloves shall be replaced immediately when physically damaged or worn. Preventive hand protection (skin protection cream) recommended. Wash immediately contaminated skin. Design operations thus to avoid permanent use of protective gloves.

Wear safety goggles to protect against solvent splashes.

If workers are exposed to concentrations above the exposure limit they must use appropriate, certified respirators. Use half-mask model with cartridge or air-fed. When operators, whether spraying or not, have to work inside the spray booth, ventilation is unlikely to be sufficient to control particulates and solvent vapour in all cases. In such circumstances they should wear a compressed air-fed respirator during the spraying process until such time as the particulates and solvent vapour concentration has fallen below the exposure limits.

Personal should wear antistatic clothings made of natural fiber or of high temperature resistant synthetic fiber. All parts of the body should be washed after contact.

Stable under normal conditions.

No decomposition if stored and applied as directed.

No dangerous reaction known under conditions of normal use. There are no data available on the preparation itself.

Stable under recommended storage and handling conditions (See section 7).

oxidizing agents, strongly alkaline and strongly acid materials

When exposed to high temperatures may produce hazardous decomposition products such as carbon monoxide and dioxide, smoke, oxides of nitrogen.