Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ARC 855(E) Part B
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
ARC Polymer Composite to be used with ARC 855(E) (Part A). Repair damage caused by impact, abrasion, erosion or corrosion; rebuild worn areas; fill holes and cracks; provide abrasion resistant surfaces.
Uses advised against
No information available.
Manufacturers & Suppliers
Chesterton International GmbH
manufacturer
Am Lenzenfleck 23, DE-85737 Ismaning GERMANY
+49 89 99 65 46 - 0
http://www.chesterton.com
Emergency Contacts
GIZ-Nord
+49(0) 551 - 1 92 40
24h
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 3-aminomethyl-3,5,5-trimethylcyclohexylamine EC: 220-666-8 | 2855-13-2 | 30 - 60% | Yes |
| benzyl alcohol EC: 202-859-9 | 100-51-6 | 30 - 60% | Yes |
| 5-Amino-1, 3, 3-trimethylclohexanemethanamine reaction products with 2,2'-[(1-methylethylidene)bis(4,1-phenyleoxymethylene)]bis[ox | 68609-08-5 | 15 - 40% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove casualty to fresh air and keep warm and at rest. In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible).
After contact with skin, take off immediately all contaminated clothing, and wash immediately with plenty of water and soap.
Symptoms: Causes severe skin burns.
After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an ophthalmologist immediately.
Symptoms: Causes severe eye damage.
If accidentally swallowed rinse the mouth with plenty of water (only if the person is conscious) and obtain immediate medical attention. Do NOT induce vomiting.
Symptoms: Gastrointestinal complaints
Immediate Medical Attention
Immediate medical treatment required because corrosive injuries that are not treated are hard to cure.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Dry extinguishing powder. Carbon dioxide (CO2). alcohol resistant foam. Water spray jet
Full water jet
In case of fire may be liberated: Carbon monoxide Carbon dioxide (CO2). Nitrogen oxides (NOx)
Firefighter Protection
Wear a self-contained breathing apparatus and chemical protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Remove persons to safety.
Do not allow to enter into surface water or drains. Cover drains. Adverse environmental effects
Absorb with liquid-binding material
Materials: sand, diatomaceous earth, acid- or universal binding agents
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wear personal protection equipment (refer to section 8). Avoid contact with skin, eyes and clothes. Avoid breathing dust/fume/gas/mist/vapours/spray. When using do not eat, drink or smoke. Never use pressure to empty container. Keep/Store only in original container.
Keep/Store only in original container.
When using do not eat, drink or smoke. Wash hands before breaks and after work. Used working clothes should not be worn outside the work area. Street clothing should be stored separately from work clothing.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate ventilation as well as local exhaustion at critical locations.
Tested protective gloves must be worn: DIN EN 374 NBR (Nitrile rubber), Butyl caoutchouc (butyl rubber) Thickness of the glove material >= 0,4 mm Breakthrough times and swelling properties of the material must be taken into consideration. For special purposes, it is recommended to check the resistance to chemicals of the protective gloves mentioned above together with the supplier of these gloves. Wearing time with occasional contact (splashes): max. 480 min. (NBR (Nitrile rubber)) Wearing time with permanent contact 240 - 480 min (NBR (Nitrile rubber)) Observe the wear time limits as specified by the manufacturer.
Suitable eye protection: Eye glasses with side protection goggles
Usually no personal respirative protection necessary. If technical exhaust or ventilation measures are not possible or insufficient, respiratory protection must be worn. Combination filtering device (EN 14387) A-P3 Self-contained respirator (breathing apparatus) (DIN EN 133)
Protective clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable under storage at normal ambient temperatures.
No information available.
Keep away from sources of heat (e.g. hot surfaces), sparks and open flames.
Strong acid, Oxidising agent
No information available.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 2289
- Shipping Name
- ISOPHORONEDIAMINE
- Transport Class
- 8
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ARC 855(E) Part B?
The signal word is danger.
What is the physical form of ARC 855(E) Part B?
ARC 855(E) Part B is a liquid with clear - colourless color. It has ammonia (nh3) odor.
What is ARC 855(E) Part B used for?
ARC Polymer Composite to be used with ARC 855(E) (Part A). Repair damage caused by impact, abrasion, erosion or corrosion; rebuild worn areas; fill holes and cracks; provide abrasion resistant surfaces.
What are the hazard statements for ARC 855(E) Part B?
This substance has 4 hazard statements:
- H302: Harmful if swallowed.
- H314: Causes severe skin burns and eye damage.
- H317: May cause an allergic skin reaction.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of ARC 855(E) Part B?
The melting point is not determined and the boiling point is >200 °C.