ULTRAZOL® 9012FM

Remove to fresh air and keep at rest in a position comfortable for breathing.

Take off contaminated clothing and wash before re-use. Wash skin thoroughly with soap and water. If skin irritation occurs, get medical attention. Launder contaminated clothing before reuse.

Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.

Do NOT induce vomiting. If vomiting occurs naturally, the casualty should lean forward to reduce the risk of aspiration. Rinse mouth. Immediately call a POISON CENTER/doctor.

Symptoms: Aspiration of material due to vomiting can cause chemical pneumonitis which can be fatal.

CO2, Dry chemical or Foam. Water can be used to cool and protect exposed material.

Do not use water jet as an extinguisher, as this will spread the fire.

Vapors may cause a flash fire or ignite explosively. Prevent buildup of vapors or gases to explosive concentrations. Vapors may travel considerable distance to a source of ignition and flash back. Water may cause splattering. Container may rupture on heating. Material creates a special hazard because it floats on water.

No data available.

ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area). Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Keep unauthorized personnel away.

Dike far ahead of larger spill for later recovery and disposal.

Avoid release to the environment. Prevent further leakage or spillage if safe to do so.

Pick up free liquid for recycle and/or disposal. Residual liquid can be absorbed on inert material.

Materials: inert material

Vapours are heavier than air and will tend to accumulate in low areas. Avoid use in confined areas without adequate ventilation. Do not handle until all safety precautions have been read and understood. Obtain special instructions before use. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Avoid breathing dust/fume/gas/mist/vapors/spray. Avoid contact with skin. Avoid contact with eyes. Use personal protective equipment as required.

Keep cool. Store in a well-ventilated place.

Observe good industrial hygiene practices. Wash hands thoroughly after handling. Launder contaminated clothing before reuse.

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Electrically bond and ground all containers and equipment.

Material should be handled in enclosed vessels and equipment, in which case general (mechanical) room ventilation should be sufficient. Local exhaust ventilation should be used at points where dust, mist, vapors or gases can escape into the room air. Adequate ventilation should be provided so that exposure limits are not exceeded. Mechanical ventilation or local exhaust ventilation is required.

Use nitrile or neoprene gloves. Use good industrial hygiene practices. In case of skin contact, wash hands and arms with soap and water. Viton. Chemical resistant gloves. For typical use and handling of chemical substances, gloves should meet the standards set out in EN 374. For applications involving mechanical risks with potential for abrasion or puncture, the standards set out in EN 388 should be considered. For continuous contact, we suggest gloves with a minimum breakthrough time of 240 minutes, or > 480 minutes if suitable gloves can be obtained. For general applications, we recommend gloves with a thickness typically greater than 0.35 mm.

Wear tight-fitting goggles or face shield. Eye protection should meet the standards set out in EN 166.

Use respirator with an organic vapor cartridge if exposure limit is exceeded. Use self-contained breathing apparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites. Use respirator with a combination organic vapor and dust/mist cartridge. Use respirator if irritation is experienced or if the recommended exposure limit is exceeded. Respiratory Protective Equipment (RPE) is not normally required where there is adequate natural or local exhaust ventilation to control exposure. In case of insufficient ventilation, wear suitable respiratory equipment.

Gloves, coveralls, apron, boots as necessary to minimize contact. Chemical resistant boots. Wear apron or protective clothing in case of contact. Do not wear rings, watches or similar apparel that could entrap the material.

No data available. See section 6 for details.

Material is stable under normal conditions.

No data available.

Will not occur.

Excessive heat. Contact with acids. Strong oxidizing agents. Strong caustic agents. Heat, sparks, flames.

Strong oxidizing agents. Strong acids. Aluminum. Lead and lead alloys Oxidizing agents, Reactive metals, Sodium or Calcium Hypochlorite. Materials reactive with hydroxyl compounds.

Thermal decomposition or combustion may generate smoke, carbon monoxide, carbon dioxide, nitrogen oxides, and other products of incomplete combustion.

Treatment, storage, transportation, and disposal must be in accordance with applicable Federal, State/Provincial, and Local regulations.