CGL-BHT/FAME

If breathing is difficult, remove to fresh air and keep at rest in a position comfortable for breathing.

Remove and isolate contaminated clothing and shoes. Wash off immediately with soap and plenty of water. Subsequent cleansing with polyethyleneglycol 400, then again with water and soap. In case of contact with hot or molten product, cool rapidly with water. Do not attempt to remove molten product from skin because skin will tear easily.

Immediately flush eyes with plenty of water for at least 15 minutes. Continue rinsing. Remove contact lenses, if present and easy to do.

Rinse mouth. Do not induce vomiting without advice from poison control center. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Never give anything by mouth to a victim who is unconscious or is having convulsions.

Foam. Powder. Carbon dioxide (CO2).

Do not use water jet as an extinguisher, as this will spread the fire.

Porous material such as rags, paper, insulation, or organic clay may spontaneously combust when wetted with this material.

Move containers from fire area if you can do so without risk. Use standard firefighting procedures and consider the hazards of other involved materials.

Keep unnecessary personnel away. Keep away from open flames, hot surfaces and sources of ignition. Ensure adequate ventilation. Wear appropriate protective equipment and clothing during clean-up. Local authorities should be advised if significant spillages cannot be contained.

Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.

Avoid discharge into drains, water courses or onto the ground.

Following product recovery, flush area with water. Clean surface thoroughly to remove residual contamination.

Materials: absorbent material (e.g. cloth, fleece)

Avoid prolonged exposure. Avoid breathing mist or vapour. Wear appropriate personal protective equipment. Wash thoroughly after handling. Avoid contact with skin, eyes and clothing.

Store in a dry place. Store in original tightly closed container.

Wash thoroughly after handling. Observe good industrial hygiene practices.

Do not handle, store or open near an open flame, sources of heat or sources of ignition.

Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.

Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. After contamination with product change the gloves immediately and dispose of them according to relevant national and local regulations. Recommended: (< 1 hour) Polyvinyl chloride - PVC, Natural rubber - NR

Wear safety glasses with side shields (or googles) in accordance with EN 166.

If engineering controls do not maintain airborne concentrations below recommended exposure limits (where applicable) or to an acceptable level (in countries where exposure limits have not been established), an approved respirator must be worn. In the case of vapor formation use a respirator with an approved filter. Respirator with a vapor filter (EN 141) Respirator with ABEK-filter.

Wear suitable protective clothing.

Environmental manager must be informed of all major releases.

Material is stable under normal conditions.

The product is stable and non-reactive under normal conditions of use, storage and transport.

No dangerous reaction known under conditions of normal use.

Contact with incompatible materials.

Strong oxidising agents.

At thermal decomposition temperatures, carbon monoxide and carbon dioxide.

Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions).

Read safety instructions, SDS and emergency procedures before handling.

Read safety instructions, SDS and emergency procedures before handling.

Read safety instructions, SDS and emergency procedures before handling.