Chloroform for analysis EMSURE® ACS,ISO,Reag. Ph Eur

After inhalation: fresh air. Immediately call in physician. If breathing stops: immediately apply artificial respiration, if necessary also oxygen.

In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Consult a physician.

After eye contact: rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses.

After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.

Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.

For this substance/mixture no limitations of extinguishing agents are given.

Carbon oxides, Hydrogen chloride gas. Not combustible. Fire may cause evolution of: Hydrogen chloride gas, Phosgene. Ambient fire may liberate hazardous vapours.

Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.

Do not let product enter drains.

Take up carefully with liquid-absorbent material (e.g. Chemizorb®). Clean up affected area.

Materials: liquid-absorbent material (e.g. Chemizorb®)

Work under hood. Do not inhale substance/mixture. Avoid generation of vapours/aerosols.

Protected from light. Tightly closed. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorized persons.

Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

Full contact Material: Viton® Minimum layer thickness: 0,7 mm Break through time: 480 min Material tested: Vitoject® (KCL 890 / Aldrich Z677698, Size M) Splash contact Material: butyl-rubber Minimum layer thickness: 0,7 mm Break through time: 10 min Material tested: Butoject® (KCL 898) This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses

required when vapours/aerosols are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type AX The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.

protective clothing

Do not let product enter drains.

The product is chemically stable under standard ambient conditions (room temperature). Contains the following stabilizer(s): ethanol (1 %)

No data available

Risk of explosion with: Ammonia, Amines, nitrogen oxides, bases, Oxygen, alkali amides, organic nitro compounds, strong alkalis, Fluorine, peroxi compounds, Alkaline earth metals, Alkali metals, Powdered metals, Methanol with alcoholates, Methanol with strong alkalis, Iron in powder form, magnesium in powder form, various alloys, sensitive to shock, Methanol with Sodium hydroxide, Oxygen with alkali compounds, Aluminum in powder form, Acetone with alkali compounds, Potassium sensitive to shock, phosphines, bis(dimethylamino)dimethyl tin, nonmetallic hydrogen compounds, Powdered metals, Light metals, Ketones, mineral acids, Strong oxidizing agents, semimetallic hydrogen compounds, sodium sensitive to shock. Violent reactions possible with:

Sensitivity to light, heat-sensitive

Ammonia, Amines, nitrogen oxides, bases, Oxygen, alkali amides, organic nitro compounds, strong alkalis, Fluorine, peroxi compounds, Alkaline earth metals, Alkali metals, Powdered metals, Methanol, alcoholates, Sodium hydroxide, alkali compounds, Aluminum, Acetone, Potassium, phosphines, bis(dimethylamino)dimethyl tin, nonmetallic hydrogen compounds, Light metals, Ketones, mineral acids, Strong oxidizing agents, semimetallic hydrogen compounds, sodium

In the event of fire: see section 5

See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.