Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ST 03003 LD
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Plastic additive, SU3 Industrial uses, SU12 Manufacture of plastics products, PC32 Polymer preparations and compounds, PROC5, PROC6, PROC8a, PROC14, PROC23, ERC3, ERC5, AC13
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
CONSTAB Polyolefin Additives GmbH
manufacturer
Industriestrasse Möhnetal 16, D-59602 Rüthen
+49(0)2952/819-0
Emergency Contacts
CONSTAB Polyolefin Additives GmbH
+49(0)2952-819-0
8:00-16:00
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Plastic additive
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
After contact with the molten product, cool rapidly with cold water. Do not pull solidified product off the skin.
Rinse opened eye for several minutes under running water.
If symptoms persist consult doctor. A person vomiting while laying on their back should be turned onto their side.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use fire extinguishing methods suitable to surrounding conditions.
Water with full jet
Formation of toxic gases is possible during heating or in case of fire.
Firefighter Protection
Wear self-contained respiratory protective device. Wear fully protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Particular danger of slipping on leaked/spilled product.
Do not allow to enter sewers/ surface or ground water.
Pick up mechanically.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Store in cool, dry place in tightly closed receptacles. Keep away from heat and direct sunlight. Ensure good ventilation/exhaustion at the workplace. Prevent formation of dust.
Store in a cool location. Store only in the original receptacle. Store in cool, dry conditions in well sealed receptacles. Protect from contamination.
Keep ignition sources away - Do not smoke. Protect from heat.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see section 7.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Safety glasses
Not necessary if room is well-ventilated.
Protective work clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications. No decomposition if used and stored according to specifications.
No further relevant information available.
Reacts with strong acids and oxidising agents.
No further relevant information available.
Reacts with strong acids and oxidising agents.
Poisonous gases/vapours, Carbon monoxide and carbon dioxide, Phosphorus oxides (e.g. P2O5)
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed together with household garbage. Do not allow product to reach sewage system. Disposal must be made according to official regulations.
Must not be disposed together with household garbage. Do not allow product to reach sewage system. Disposal must be made according to official regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- not regulated
- Shipping Name
- not regulated
- Transport Class
- not regulated
- Packing Group
- not regulated
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ST 03003 LD?
The signal word is no signal word.
What is the physical form of ST 03003 LD?
ST 03003 LD is a solid appearing as granulate with according to product specification color. It has product specific odor.
What is ST 03003 LD used for?
Plastic additive, SU3 Industrial uses, SU12 Manufacture of plastics products, PC32 Polymer preparations and compounds, PROC5, PROC6, PROC8a, PROC14, PROC23, ERC3, ERC5, AC13
What is the melting point of ST 03003 LD?
The melting point is Undetermined. and the boiling point is Undetermined..