Chemical Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
Crown 9106 Tap Tool - Aerosol is a clear water white substance commonly used use for drilling, tapping, threading, boring, broaching,reaming,turning and engraving..
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
Hazard Classifications
GHS Hazard Pictograms & Safety Symbols
GHS02
GHS04
GHS07
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
- H220: Extremely flammable gas.
- H222: Extremely flammable aerosol.
- H226: Flammable liquid and vapor.
- H229: Pressurized container: may burst if heated
- H315: Causes skin irritation.
- H319: Causes serious eye irritation.
- H335: May cause respiratory irritation.
Precautionary Statements
- P101: If medical advice is needed, have product container or label at hand
- P102: Keep out of reach of children
- P103: Read label before use
- P210: Keep away from heat/sparks/open flames/hot surfaces - no smoking
- P211: Do not spray on an open flame or other ignition source
- P251: Pressurized container: Do not pierce or burn, even after use
- P261: Avoid breathing dust/fume/gas/mist/vapours/spray
- P262: Do not get in eyes, on skin, or on clothing
- P264: Wash ... thoroughly after handling
- P280: Wear protective gloves/eye protection/face protection
- P303+P361+P353: If on skin and hair, remove/takeoff immediately all contaminated clothing. Rinse skin with water/shower.
- P410+P412: Protect from sunlight. Do not expose to temperatures exceeding 50℃/122ºF
- P501: Dispose of contents/container in accordance with local/regional/national/international regulation
Chemical Manufacturers & Supply Chain
Authorized suppliers, manufacturers, and distribution network information
Aervoe Industries Incorporated
manufacturer
1100 Mark Circle Gardnerville, Nevada 89410
US
1-775-782-0100
24/7 Emergency Response & Poison Control
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
CHEMTREC
1-800-424-9300
US
24 hrs
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
MixtureChemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Para- Chlorobenzotrifluoride EC: 202-681-1 | 98-56-6 | 30-60% | ⚠️ Hazardous |
| Hydrocarbon Propellant EC: 270-705-8 | 68476-86-8 | 10-30% | ⚠️ Hazardous |
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
🫁 Inhalation Exposure
Remove victim to fresh air and provide oxygen if breathing is difficult. If not breathing, give artificial respiration, preferably mouth to mouth. Get medical attention immediately.
Symptoms:
difficulty breathing
🖐️ Skin Contact
Wash with soap and water. Remove contaminated clothing and shoes. Get medical attention immediately. Wash clothing before reuse.
👁️ Eye Contact
If contact with eyes, immediately flush eyes with plenty of water for at least 15 minutes, while holding eyelids open. Get medical attention immediately.
🍽️ Ingestion/Swallowing
If swallowed, wash out mouth with water provided the person is conscious. Do not induce vomiting. Never give anything by mouth to an unconscious person. Get medical attention immediately.
🚨 Immediate Medical Attention Required
If symptoms persist, always call a doctor. Get medical attention immediately.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Exposure Controls & Personal Protective Equipment (PPE)
Occupational exposure limits, engineering controls, and required safety equipment
🏭 Engineering Controls
Ensure adequate ventilation. A system of local and/or general exhaust is recommended to keep employee exposures below the Airborne Exposure Limits. Keep away from sources of ignition. Take precautionary measures against static discharge.
👁️ Eye Protection
Eye & face protection devices such as safety glasses, safety goggles or face shield are recommended.
😷 Respiratory Protection
Use only in an adequately ventilated area. For unknown vapor concentrations use a positive-pressure, pressure-demand, self-contained breathing apparatus (SCBA).
🦺 Skin/Body Protection
Wear the appropriate protective clothing, including boots, gloves, lab coat, apron or coveralls, as appropriate, to prevent skin contact.
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for Crown 9106 Tap Tool - Aerosol?
The signal word for this substance is "danger".
What is the physical form of Crown 9106 Tap Tool - Aerosol?
Crown 9106 Tap Tool - Aerosol is a gas appearing as clear water white with water white color. It has ethereal odor odor.
What is the solubility of Crown 9106 Tap Tool - Aerosol?
Negligible
What is Crown 9106 Tap Tool - Aerosol used for?
Use for drilling, tapping, threading, boring, broaching,reaming,turning and engraving.
What are the hazard statements for Crown 9106 Tap Tool - Aerosol?
This substance has 7 hazard statements: H220: Extremely flammable gas. H222: Extremely flammable aerosol. H226: Flammable liquid and vapor. H229: Pressurized container: may burst if heated H315: Causes skin irritation. H319: Causes serious eye irritation. H335: May cause respiratory irritation.
What is the melting point of Crown 9106 Tap Tool - Aerosol?
The melting point is N/AV and the boiling point is N/AV.