Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Titriplex® II for analysis (ethylenedinitrilotetraacetic acid) ACS, Reag. Ph Eur
- Product Code
- 1.08417
- Chemical Name
- ethylenedinitrilotetraacetic acid
Regulatory Identifiers
- CAS Number
- 60-00-4 Check regulations →
- REACH No.
- 01-2119486399-18-XXXX
Identified Uses
Reagent for analysis
Manufacturers & Suppliers
Merck Life Science UK Limited
national supplier
New Road, The Old Brickyard, GILLINGHAM, Dorset, SP8 4XT, UNITED KINGDOM
+44 (0)1747 833-000
Emergency Contacts
CHEMTREC
+44 (0)870 8200418
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Formula : C10H16N2O8 Molecular weight : 292.24 g/mol CAS-No. : 60-00-4 EC-No. : 200-449-4 Index-No. : 607-429-00-8
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethylenediaminetetraacetic acid EC: 200-449-4 | 60-00-4 | 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses.
After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon dioxide (CO2) Foam Dry powder
For this substance/mixture no limitations of extinguishing agents are given.
Carbon oxides, Nitrogen oxides (NOx), Combustible. Fire may cause evolution of: nitrogen oxides. Development of hazardous combustion gases or vapours possible in the event of fire.
Suppress (knock down) gases/vapors/mists with a water spray jet.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Evacuate the danger area, observe emergency procedures, consult an expert.
Take up dry. Clean up affected area.
Related Products
Similar products with comparable safety profiles
Titriplex® III for analysis (ethylenedinitrilotetraacetic acid, disodium salt dihydrate) ACS, ISO, Reag. Ph Eur
CAS: 6381-92-6
Titriplex® III GR for analysis (ethylenedinitrilotetraacetic acid, disodium salt dihydrate) ACS, ISO, Reag. Ph Eur
---
Titriplex® IV for analysis (1,2-cyclohexylenedinitrilotetraacetic acid monohydrate)
CAS: 125572-95-4
Tris(hydroxymethyl)aminomethane GR for analysis buffer substance ACS,Reag. Ph Eur
CAS: 77-86-1
HEXAMETHYLENETETRAMINE, REAGENT, ACS
---
Lead(II) acetate trihydrate for analysis EMSURE® ACS, Reag. Ph Eur
CAS: 6080-56-4
Ethylenediaminetetraacetic acid, ACS
CAS: 60-00-4
tri-Sodium citrate dihydrate AnalaR NORMAPUR® ACS, Reag. Ph. Eur. analytical reagent
CAS: 6132-04-3
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For precautions see section 2.2.
Tightly closed. Dry. Recommended storage temperature see product label.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Nitrile rubber, Minimum layer thickness: 0.11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0.11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Standards compliance: EN374.
Safety glasses, tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Required when dusts are generated. Recommended Filter type: Filter type P2. Standards: DIN EN 143, DIN 14387.
protective clothing
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.
Violent reactions possible with: Strong oxidizing agents, Strong bases
no information available
Copper, Copper alloys, Nickel
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Waste material must be disposed of in accordance with the national and local regulations. Leave chemicals in original containers. No mixing with other waste.
Leave chemicals in original containers. No mixing with other waste.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- Shipping Name
- Not dangerous goods
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Titriplex® II for analysis (ethylenedinitrilotetraacetic acid) ACS, Reag. Ph Eur?
The signal word is warning.
What is the physical form of Titriplex® II for analysis (ethylenedinitrilotetraacetic acid) ACS, Reag. Ph Eur?
Titriplex® II for analysis (ethylenedinitrilotetraacetic acid) ACS, Reag. Ph Eur is a solid with off-white color. It has odorless odor.
What is Titriplex® II for analysis (ethylenedinitrilotetraacetic acid) ACS, Reag. Ph Eur used for?
Reagent for analysis
What are the hazard statements for Titriplex® II for analysis (ethylenedinitrilotetraacetic acid) ACS, Reag. Ph Eur?
This substance has 1 hazard statement:
- H319: Causes serious eye irritation.
What is the melting point of Titriplex® II for analysis (ethylenedinitrilotetraacetic acid) ACS, Reag. Ph Eur?
The melting point is > 220 °C and the boiling point is No data available.