Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LCL 30.1
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coolant
Uses advised against
No information available.
Manufacturers & Suppliers
Lorch Schweisstechnik GmbH
manufacturer
Im Anwänder 24-26, D-71549 Auenwald-Mittelbrüden
+49 7191.503.0
http://www.lorch.biz
Emergency Contacts
GIZ-Nord
+49(0) 551 - 1 92 40
24h
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Provide fresh air.
After contact with skin, wash immediately with plenty of water and soap. Remove contaminated, saturated clothing immediately.
After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an ophthalmologist immediately.
If accidentally swallowed rinse the mouth with plenty of water (only if the person is conscious) and obtain immediate medical attention. Do NOT induce vomiting.
Immediate Medical Attention
First Aid, decontamination, treatment of symptoms.
Medical Treatment
First Aid, decontamination, treatment of symptoms.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate ventilation as well as local exhaustion at critical locations. Work in well-ventilated zones or use proper respiratory protection. Ground and bond container and receiving equipment. Carry out filling operations only at stations with exhaust ventilation facilities.
Tested protective gloves must be worn: DIN EN 374 NBR (Nitrile rubber) NR (natural rubber, natural latex) Butyl caoutchouc (butyl rubber) Thickness of the glove material >= 0,4 mm Breakthrough times and swelling properties of the material must be taken into consideration. For special purposes, it is recommended to check the resistance to chemicals of the protective gloves mentioned above together with the supplier of these gloves. Wearing time with occasional contact (splashes): max. 480 min. (NBR (Nitrile rubber)) Wearing time with permanent contact 240 - 480 min (NBR (Nitrile rubber)) Observe the wear time limits as specified by the manufacturer. Wear cotton undermitten if possible.
Eye glasses with side protection, goggles
If technical exhaust or ventilation measures are not possible or insufficient, respiratory protection must be worn. Suitable respiratory protection apparatus: Full-/half-/quarter-face masks (DIN EN 136/140) ABEK-P3
Wear anti-static footwear and clothing Street clothing should be stored separately from work clothing. Take off immediately all contaminated clothing and wash it before reuse.
No information available.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LCL 30.1?
The signal word is warning.
What is the physical form of LCL 30.1?
LCL 30.1 is a liquid with colourless color. It has characteristic odor.
What is the solubility of LCL 30.1?
No information available.
What is LCL 30.1 used for?
Coolant
What are the hazard statements for LCL 30.1?
This substance has 3 hazard statements:
- H302: Harmful if swallowed.
- H319: Causes serious eye irritation.
- H373: May cause damage to organs through prolonged or repeated exposure.
What is the melting point of LCL 30.1?
The melting point is not determined and the boiling point is ~ 100 C.