Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- PU Top Finish Matt
- Product Code
- 51.0022
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Finish
Manufacturers & Suppliers
Global Paint Products BV
Veesteeg 11-13, 6657 KH Boven-Leeuwen
+31 487 595160
Emergency Contacts
Nationaal Vergiftigingen Informatie Centrum
088-7558000
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| TRIMETHYLOLPROPAAN EC: 201-074-9 | 77-99-6 | 0.3% | Yes |
| 1,2-BENZISOTHIAZOL-3(2H)-ONE EC: 220-120-9 | 2634-33-5 | 0.005 - 0.05% | Yes |
| REACTION MASS OF: 5-CHLORO-2-METHYL-4-ISOTHIAZOLIN-3-ONE AND 2-METHYL-2H-ISOTHIAZOL-3-ONE (3:1) | 55965-84-9 | 0.00015 - 0.0015% | Yes |
For full text of Hazard- and EU Hazard-statements: see SECTION 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove casualty to fresh air and keep warm and at rest. If breathing is irregular or stopped, administer artificial respiration.
Remove contaminated, saturated clothing immediately. After contact with skin, wash immediately with plenty of water and soap. Do not wash with: Solvents/Thinner
In case of contact with eyes flush immediately with plenty of flowing water for 10 to 15 minutes holding eyelids apart and consult an ophthalmologist. Remove contact lenses, if present and easy to do. Continue rinsing.
If accidentally swallowed rinse the mouth with plenty of water (only if the person is conscious) and obtain immediate medical attention. Keep at rest. Do NOT induce vomiting.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
alcohol resistant foam, Carbon dioxide (CO2), Extinguishing powder, Water mist
Strong water jet
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard.
Cool endangered containers with water in case of fire.
Firefighter Protection
Use suitable breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Remove all sources of ignition. Do not inhale the vapour. See protective measures under point 7 and 8.
Do not allow to enter into surface water or drains.
Clear spills immediately. Contain and collect spillage. Clean with detergents. Avoid solvent cleaners.
Materials: non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous earth
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with skin, eyes and clothes. Do not breathe gas/vapour/aerosol. When using do not eat, drink, smoke. See chapter 8 of the safety data sheet (Personal protection equipment) Never use pressure to empty container. Keep/Store only in original container. Comply with the health and safety at work laws.
Keep container tightly closed and in a well-ventilated place. Store between +5 and 35 °C in a dry, well ventilated place away from sources of heat and direct sunlight.
When using do not eat, drink, smoke.
When using do not smoke. Keep away from sources of heat.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide for sufficient ventilation. This can be achieved by local exhaust or general exhaust air collection.
Use protective gloves. Suitable material : NBR (Nitrile rubber). Required properties : EN ISO 374. Breakthrough time : 480 min. Thickness of the glove material : ±0.1 / 0.4 mm. Additional hand protection measures : Check protective gloves before each use concerning their normal condition.
Use tightly fitting safety glasses.
By spraying: air fed respirator. By other operations than spraying: in well ventilated areas, airfed respirators could be replaced by a combination of charcoal filter and particulate filter mask.
Body protection: not required.
Do not allow to enter into surface water or drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage and handling conditions (See section 7).
No information available.
Keep away from oxidizing agents, strongly alkaline and strongly acid materials in order to avoid exothermic reactions.
When exposed to high temperatures may produce hazardous decomposition products such as carbon monoxide and dioxide, smoke, oxides of nitrogen.
No information available.
Carbon dioxide. Carbon monoxide Nitrogen oxides (NOx).
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Waste disposal according to directive 2008/98/EC, covering waste and dangerous waste.
Avoid release to the environment. Refer to special instructions/safety data sheet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for PU Top Finish Matt?
The signal word is no signal word.
What is the physical form of PU Top Finish Matt?
PU Top Finish Matt is a liquid with white color. It has noticeable. odor.
What is PU Top Finish Matt used for?
Finish
What is the melting point of PU Top Finish Matt?
The melting point is No data available and the boiling point is 100 °C.