Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- RENISO PAG 46
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricant
Uses advised against
No uses advised against identified.
Manufacturers & Suppliers
FUCHS LUBRICANTS (UK) PLC.
manufacturer
New Century Street, ST1 5HU Hanley
+44 (0) 1782 203700
Emergency Contacts
UK NHS
111
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture based on polyglycole.
Notes
The components are not hazardous or are below required disclosure limits.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of symptoms.
Wash with soap and water.
Promptly wash eyes with plenty of water while lifting the eye lids.
Rinse mouth thoroughly.
Immediate Medical Attention
Get medical attention if symptoms occur.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, fire extinguishing powder or fog like water spraying. Extinguish larger fires with alcohol resistant foam or spray water with suitable surfactant added
Water with a full water jet.
During fire, gases hazardous to health may be formed.
Move container from fire area if it can be done without risk.
Firefighter Protection
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
In case of spills, beware of slippery floors and surfaces.
Prevent from spreading (e.g. by binding or oil barriers). Avoid release to the environment. Environmental manager must be informed of all major spillages. Prevent further leakage or spillage if safe to do so. Do not allow to enter drainage system, surface or ground water.
Absorb with liquid-binding material. Dispose of the material collected according to regulations.
Materials: sand, diatomite, acidbinders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Prevent formation of aerosols. Do not eat, drink or smoke when working with the product. Take usual precautions when handling mineral oil products or chemical products. Observe good industrial hygiene practices.
Do not heat up to temperatures close to the flash point.
Do not eat, drink or smoke when working with the product. Observe good industrial hygiene practices.
Do not heat up to temperatures close to the flash point.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate ventilation. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.
Material: Nitrile butyl rubber (NBR). Min. Breakthrough time: >= 480 min Recommended thickness of the material: >= 0,38 mm. Avoid long-term and repeated skin contact. Suitable gloves can be recommended by the glove supplier. Use skin protection cream for preventive skin protection. Protective gloves, where permitted in acc. to safety directions. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Safety glasses (EN 166) recommended during refilling.
Ensure good ventilation/exhaustion at the workplace. Avoid breathing vapour/ aerosol.
Do not carry cleaning cloths impregnated with the product in trouser pockets. Wear suitable protective clothing.
No data available.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal use conditions.
Stable under normal use conditions.
Stable under normal use conditions.
Stable under normal use conditions.
Strong oxidizing substances. Strong acids. Strong bases.
Thermal decomposition or combustion may liberate carbon oxides and other toxic gases or vapors.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose in accordance with all applicable regulations.
Do not empty into drains; dispose of this material and its container in a safe way.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- Transport Class
- Non-dangerous goods
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for RENISO PAG 46?
The signal word is no signal word.
What is the physical form of RENISO PAG 46?
RENISO PAG 46 is a liquid appearing as liquid with colorless color. It has characteristic odor.
What is the solubility of RENISO PAG 46?
No data available.
What is RENISO PAG 46 used for?
Lubricant