Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ESI Xtreme Pro - Comp. A
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Adhesive mortar for fastening elements A-component (resin)
Uses advised against
no restriction
Manufacturers & Suppliers
EXPANDET SCREW ANCHORS A/S
manufacturer
Svendebuen 2-6, DK-3230 Græsted
+45 70227979
Emergency Contacts
Emergency Contact
+45 70227979
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| ethylene dimethacrylate EC: 202-617-2 | 97-90-5 | 10 - 15% | Yes |
| Methacrylic acid, monoester with propane-1,2-diol EC: 248-666-3 | 27813-02-1 | 5 - 10% | Yes |
| Quartz (< 10μm) EC: 238-878-4 | 14808-60-7 | 1 - 5% | Yes |
| 1,1'-(p-Tolylimino)dipropan-2-ol EC: 254-075-1 | 38668-48-3 | 1% | Yes |
This mixture includes a fine fraction of crystalline quartz. However, alveolar permeability can be ruled out as the quartz is irreversibly bound into the paste-like component and therefore not freely available. Subsequent drilling, grinding or other treatment can also not result in the free availability of this alveolar permeable quartz. Pursuant to Article 6 of CLP Regulation 1272/2008/EU classification and labelling as SLOT RE 2 is not required.
Notes
SVHC Liste (Candidate List of Substances of Very High Concern for authorisation): substances are not contained or are below 0.1%.
First Aid Measures
Emergency procedures for chemical exposure incidents
Provide fresh air. When in doubt or if symptoms are observed, get medical advice.
Take off immediately all contaminated clothing and wash it before reuse. Medical treatment necessary.
Rinse immediately carefully and thoroughly with eye-bath or water. In case of eye irritation consult an ophthalmologist.
Rinse mouth immediately and drink plenty of water.
Immediate Medical Attention
Medical treatment necessary.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Extinguishing powder, Water spray jet, Carbon dioxide (CO2).
Full water jet, Foam.
Pyrolysis products, toxic, Carbon monoxide.
In case of fire and/or explosion do not breathe fumes.
Firefighter Protection
Wear a self-contained breathing apparatus and chemical protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Provide adequate ventilation. Do not breathe gas/fumes/vapour/spray. Avoid contact with skin, eyes and clothes. Use personal protection equipment.
Do not allow to enter into surface water or drains.
Take up mechanically.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only outdoors or in a well-ventilated area. When using do not eat, drink or smoke. Wash hands before breaks and after work.
Keep container tightly closed. Keep only in the original container in a cool, well-ventilated place. storage temperature: 5-25°C
When using do not eat, drink or smoke. Wash hands before breaks and after work.
No special fire protection measures are necessary.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
When handling with chemical substances, protective gloves must be worn with the CE-label including the four control digits. The quality of the protective gloves resistant to chemicals must be chosen as a function of the specific working place concentration and quantity of hazardous substances. For special purposes, it is recommended to check the resistance to chemicals of the protective gloves mentioned above together with the supplier of these gloves. Wearing time with occasional contact (splashes): 0,4mm NBR (Nitrile rubber) >480min (EN374) Wearing time with permanent contact 0,5mm NBR (Nitrile rubber) >480min (EN374)
Wear eye/face protection.
In case of inadequate ventilation wear respiratory protection.
Wear suitable protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable under storage at normal ambient temperatures.
No hazardous reaction when handled and stored according to provisions.
No known hazardous reactions.
No information available.
No known hazardous decomposition products.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Do not allow to enter into surface water or drains. Do not allow to enter into soil/subsoil. Dispose of waste according to applicable legislation.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
To follow: 850/2004/EC, 79/117/EEC, 689/2008/EC
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ESI Xtreme Pro - Comp. A?
The signal word is warning.
What is the physical form of ESI Xtreme Pro - Comp. A?
ESI Xtreme Pro - Comp. A is a paste with light beige color.
What is the solubility of ESI Xtreme Pro - Comp. A?
not determined
What is ESI Xtreme Pro - Comp. A used for?
Adhesive mortar for fastening elements A-component (resin)
What are the hazard statements for ESI Xtreme Pro - Comp. A?
This substance has 2 hazard statements:
- H317: May cause an allergic skin reaction.
- H335: May cause respiratory irritation.
What is the melting point of ESI Xtreme Pro - Comp. A?
The melting point is not determined and the boiling point is not determined.