Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- CHLORIDE ISE STANDARD
- Product Code
- 51344772
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Laboratory Chemicals
Manufacturers & Suppliers
Reagecon Diagnostics Ltd.
manufacturer
Shannon Free Zone, Shannon, Co. Clare, Ireland.
+353 61 472622
Emergency Contacts
Reagecon Diagnostics Ltd.
011-353-86-0224204
24 HOUR
Reagecon Diagnostics Ltd.
00-353-86-0224204
24 HOUR
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Purified Water EC: 231-791-2 | --- | --- | No |
For the wording of the listed risk phrases refer to section 16.
Notes
Dangerous components: Void
First Aid Measures
Emergency procedures for chemical exposure incidents
Provide fresh air, warmth and rest. When breathing is difficult, properly trained personnel may assist affected person by administering oxygen. Obtain medical attention if any discomfort continues.
Promptly wash eyes with plenty of water for up to 15 minutes. Open eyes wide apart and rinse well to remove any contact lenses. Do not remove contact lenses by hand. Continue to rinse. Get medical attention if symptoms persist.
If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
No further relevant information available.
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Not required.
Dilute with plenty of water.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
No special measures required.
No special requirements.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Additional information about design of technical facilities: No further data; see item 7.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Always ensure that gloves are inspected before use. Selection of protective gloves must include consideration of the penetration times along with rates of diffusion and degradation. The selected glove should comply with the specifications of EU Directive 89/686/EEC and the standard EN374 derived from it. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. Nitrile gloves are recommended for splash contact. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific use scenario. Penetration time of glove material: The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
Goggles recommended during refilling
Not required.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Smaller quantities can be disposed of with household waste.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for CHLORIDE ISE STANDARD?
The signal word is no signal word.
What is the physical form of CHLORIDE ISE STANDARD?
CHLORIDE ISE STANDARD is a liquid appearing as liquid with according to product specification color. It has characteristic odor.
What is the solubility of CHLORIDE ISE STANDARD?
Fully miscible.
What is CHLORIDE ISE STANDARD used for?
Laboratory Chemicals
What is the melting point of CHLORIDE ISE STANDARD?
The melting point is 0 °C and the boiling point is 100 °C.