Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ARMEEN HT
- Chemical Name
- Amines, C16-18 Alkyl
Regulatory Identifiers
- CAS Number
- N/A
- REACH No.
- 01-2119473799-15-0003
Identified Uses
Specific use(s): Refer to attached exposure scenario Annex.
Manufacturers & Suppliers
Nouryon Functional Chemicals AB
Stenunge Allé 3 SE 444 85 Stenungsund Sweden
+4630385000
Emergency Contacts
Emergency Contact
+31 57 06 79211
24 hours
US-CHEMTREC
1-800-424-9300
CA-CANUTEC
1-613-996-6666
Emergency Contact
+81 (836) 74 8810
Emergency Contact
+86 532 8388 9090
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS08
GHS09
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| (Hydrogenated tallow) amine EC: 262-976-6 | 61788-45-2 | 90 - 100% | Yes |
Notes
For the full text of the H-Statements mentioned in this Section, see Section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Obtain medical attention immediately.
Take off contaminated clothing and shoes immediately. Carefully remove paste or solidified product. Wash skin immediately with 0,5 % acetic acid in water, and then with soap and water. If skin irritation persists, call a physician.
Symptoms: Skin irritation, if untreated may be prolonged and serious (eg necrosis). Causes skin irritation.
In case of contact with eyes, rinse immediately with 0.5% acetic acid in water for a few minutes, followed by rinsing with plenty of water for as long as possible. Eyelids should be held away from the eyeball to ensure thorough rinsing. Get medical attention immediately. Continue to rinse during transport. Remove contact lenses. Protect unharmed eye. Keep eye wide open while rinsing.
Symptoms: Causes serious eye damage.
Clean mouth with water and drink afterwards plenty of water. Do NOT induce vomiting. Never give anything by mouth to an unconscious person.
Symptoms: May be fatal if swallowed and enters airways.
Immediate Medical Attention
Immediate medical attention is required. Get medical attention immediately.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
High volume water jet
Treat as oil fire. Do not use a solid water stream as it may scatter and spread fire.
Water spray may be ineffective unless used by experienced firefighters.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Evacuate personnel to safe areas. Only qualified personnel equipped with suitable protective equipment may intervene. Prevent unauthorised persons entering the zone.
Do not flush into surface water or sanitary sewer system. Discharge into the environment must be avoided.
Pick up and arrange disposal without creating dust.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For personal protection see section 8. Avoid formation of respirable particles. Avoid contact with skin, eyes and clothing. Smoking, eating and drinking should be prohibited in the application area. Dispose of rinse water in accordance with local and national regulations.
Prevent unauthorized access. Keep container tightly closed in a dry and well-ventilated place. Avoid elevated temperatures. No decomposition if stored and applied as directed.
Smoking, eating and drinking should be prohibited in the application area.
Provide appropriate exhaust ventilation at places where dust is formed.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide eyewash station and safety shower. Keep solutions of 0.5% acetic acid in water close at hand.
Nitrile rubber; butyl-rubber
Tightly fitting safety goggles
In the case of dust, vapour or aerosol formation use a respirator with an approved filter. Wear full face mask supplied with: Combination filter: ABEKP.
Protective suit
Do not flush into surface water or sanitary sewer system. Discharge into the environment must be avoided.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Stable under normal conditions.
No dangerous reaction known under conditions of normal use.
None known.
Reacts with copper, aluminium, zinc and their alloys.
No hazardous decomposition products are known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN 3077
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S.
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ARMEEN HT?
The signal word is no signal word.
What is the physical form of ARMEEN HT?
ARMEEN HT is a solid with light yellow color. It has ammoniacal odor.
What is the solubility of ARMEEN HT?
Soluble in ethanol and 2-propanol.
What is ARMEEN HT used for?
Specific use(s): Refer to attached exposure scenario Annex.
What is the melting point of ARMEEN HT?
The melting point is 40 - 55 °C and the boiling point is > 300 °C.