Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ALCUPOL F5612
- Chemical Name
- Polyol ether.
Regulatory Identifiers
- CAS Number
- 25791-96-2 Check regulations →
- EC Number
- 500-044-5 Check regulations →
Identified Uses
Consult technical information.
Manufacturers & Suppliers
REPSOL QUÍMICA, S.A.
manufacturer
Méndez Álvaro, 44 28045 - MADRID, Spain
+34 917538000/+34 917538100, +34 926419500
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Polyol polyether stabilized with additives.
First Aid Measures
Emergency procedures for chemical exposure incidents
wash the affected area with soap and hot water.
Symptoms: Contact with skin may cause irritation.
Keep eyelids open and wash immediately with plenty of water for at least 15 minutes.
Symptoms: slight transient pain and irritation similar to that caused by a mild soap.
If the affected person is conscious, give him/her milk or water to drink. Seek medical care.
Symptoms: If swallowed, it may irritate the digestive tract and cause nausea, vomiting and abdominal discomfort.
Immediate Medical Attention
Seek medical care.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray, dry chemical powder and CO2.
Water applied directly in jet stream may disperse the product.
The product is not readily flammable; however, it will burn if enclosed in fire.
Firefighter Protection
Clothing and gloves resistant to fire and SCBA.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Prohibit entry of unnecessary personnel.
Collect with sand or other non-combustible absorbent material and place into containers for later disposal.
Dike far ahead of liquid spillage and using vacuum equipment, pump into containers for later disposal.
Keep the product away from drains, sewers and waterways. Hazard of physical contamination in case of accidental releases.
Collect with sand or other non-combustible absorbent material and place into containers for later disposal. Dike far ahead of liquid spillage and using vacuum equipment, pump into containers for later disposal.
Materials: sand or other non-combustible absorbent material
Related Products
Similar products with comparable safety profiles
ALCUPOL® P-2321, ALCUPOL® P-2621, ALCUPOL® P-2921, ALCUPOL® P-3021, ALCUPOL® P-3041, ALCUPOL® P-3041N, ALCUPOL® P-3091, ALCUPOL® P-3091S, ALCUPOL® P-3421, ALCUPOL® P-3621, ALCUPOL® P-3621S
---
Alusol SL 61 XBB
UFI: 2UC2-F0CE-P00P-QX5R
S1220 ALUPES /PU
---
ARALDITE® MY 721 CH
CAS: 28768-32-3
Alcomer® 7523D
---
ARCOL® POLYOL F-3040
---
ARALDITE® MY 0510
CAS: 5026-74-4
PLIXXOPOL RC 4860C041
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wear protective clothing to avoid prolonged contact with the product. Do not smoke, drink, or eat during handling. Do not handle damaged containers unless wearing appropriate protective equipment to avoid direct contact. Ensure safe systems of work. When filling or handling containers use appropriate waterproof suits, gloves, and shoes, and safety goggles or face-shields to prevent splashes.
It must be stored in steel or polyethylene containers, properly labeled and sealed, placed in cool, well-ventilated areas. Protect containers against the inclemencies of the weather.
Good personal hygiene procedures must be observed. Do not smoke, drink, or eat during handling.
use pumps and connections grounded to prevent electrostatic charge.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Gloves to avoid contact.
Safety goggles or face-shields to prevent splashes.
Appropriate clothing to avoid contact.
Product should not reach the environment through wastewater or sewage. Measures to take in case of accidental release can be found in Section 6 of this information note about product safety.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions.
Oxidizing substances.
High temperatures, moisture.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Send it to authorized waste or controlled incineration facilities. Recycle and recover product if possible.
Send it to authorized waste or controlled incineration facilities. Recycle and recover product if possible. Consult with authorized agencies.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Transport in properly sealed and labeled containers.
Transport in properly sealed and labeled containers.
Transport in properly sealed and labeled containers.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ALCUPOL F5612?
The signal word is no signal word.
What is the physical form of ALCUPOL F5612?
ALCUPOL F5612 is a liquid appearing as liquid with colorless color. It has odorless odor.
What is the solubility of ALCUPOL F5612?
Alcohols, ethers, ketones, aromatic hydrocarbons and halogenated solvents.
What is ALCUPOL F5612 used for?
Consult technical information.
What is the melting point of ALCUPOL F5612?
The melting point is N/A (*) and the boiling point is N/A (*).