ALCUPOL® P-2321, ALCUPOL® P-2621, ALCUPOL® P-2921, ALCUPOL® P-3021, ALCUPOL® P-3041, ALCUPOL® P-3041N, ALCUPOL® P-3091, ALCUPOL® P-3091S, ALCUPOL® P-3421, ALCUPOL® P-3621, ALCUPOL® P-3621S

Move to fresh air. Call a physician if symptoms develop or persist.

Wash off with soap and water. Get medical attention if irritation develops and persists.

Immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention if irritation develops and persists.

Rinse mouth. Get medical attention if symptoms occur.

Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).

Do not use water jet as an extinguisher, as this will spread the fire.

During fire, gases hazardous to health may be formed such as: Carbon oxides. Nitrogen Oxides.

Move containers from fire area if you can do so without risk.

Keep unnecessary personnel away. Follow standard emergency procedure. Ensure adequate ventilation. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing.

Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.

Avoid discharge into drains, water courses or onto the ground.

Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

Materials: vermiculite, dry sand, earth, absorbent material (e.g. cloth, fleece)

Ensure safe systems of work or equivalent arrangements are in place to manage risks. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. Observe good industrial hygiene practices.

Store in tightly closed container.

Observe good industrial hygiene practices.

Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition.

Good general ventilation should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.

Wear suitable gloves tested to EN374. The requirements of EN 388 must be taken into account for applications involving mechanical hazards with the risk of abrasion or incision. The requirements outlined in EN 407 must be taken into consideration for tasks involving thermal hazards. The most suitable glove must be chosen in consultation with the gloves supplier, who can inform about the breakthrough time of the glove material.

Wear safety glasses with side shields (or goggles). Eye protection should meet standard EN 166.

In case of insufficient ventilation, wear suitable respiratory equipment. If engineering controls do not maintain airborne concentrations below recommended exposure limits (where applicable) or to an acceptable level (in countries where exposure limits have not been established), an approved respirator must be worn. Use a positive-pressure air-supplied respirator if there is any potential for an uncontrolled release, exposure levels are not known, or any other circumstances where air-purifying respirators may not provide adequate protection. Appropriate respirator selection should be made by a qualified professional.

Wear suitable protective clothing.

Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. Fume scrubbers, filters or engineering modifications to the process equipment may be necessary to reduce emissions to acceptable levels. Product should not reach the environment through wastewater or sewage.

Material is stable under normal conditions.

The product is stable and non-reactive under normal conditions of use, storage and transport.

No dangerous reaction known under conditions of normal use.

Contact with incompatible materials.

Strong oxidising agents.

No hazardous decomposition products are known.

Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions).