NextSDS Logo
Safety Data Sheet EN

DiaMed HbF Screening Test Staining Solution

Scan your chemical compliance

Free 10-second scan. Upload a document and check compliance instantly.

Scan Now
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
DiaMed HbF Screening Test Staining Solution
Product Code
41711

Regulatory Identifiers

CAS Number
N/A

Identified Uses

In vitro diagnostic medical device or component.

Uses advised against

No further relevant information available.

Manufacturers & Suppliers

D

DiaMed GmbH

manufacturer

Pra Rond 23, CH-1785 Cressier FR, (Switzerland/Schweiz/Suisse/Swizzera)

+41 (0)26 674 51 11

Emergency Contacts

Emergency Contact

030-274 8888

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Corr. Cat. 1A H314

GHS Pictograms

GHS05 - Corrosive

GHS05

Hazard Statements

H314 Causes severe skin burns and eye damage.

Precautionary Statements

P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P303 + P361 + P353 IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P310 Immediately call a POISON CENTER/doctor.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local/regional/ national/international regulations.

Manage your Safety Data Sheets

Organize and access chemical safety data with ease

Manage SDS
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

Mixture of substances listed below with nonhazardous additions.

Chemical Name CAS Number Concentration Hazardous
Ammonium iron (III) sulfate dodecahydrate EC: 233-382-4 7783-83-7 2.3% Yes
sulphuric acid EC: 231-639-5 7664-93-9 1.02% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

In case of unconsciousness place patient stably in side position for transportation.

Skin contact

Immediately wash with water and soap and rinse thoroughly.

Eye contact

Rinse opened eye for several minutes under running water. Then consult a doctor.

Ingestion

Drink plenty of water and provide fresh air. Call for a doctor immediately.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.

Specific hazards

No further relevant information available.

Firefighter Protection

No special measures required.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Wear protective equipment. Keep unprotected persons away.

Environmental

No special measures required.

Cleanup methods

Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Use neutralising agent.

Materials: liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.

Storage

Keep container tightly sealed. No special requirements for storerooms and receptacles.

Fire prevention

No special measures required.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

No further data; see item 7.

Hands

Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.

Eyes

Safety glasses. Tightly sealed goggles.

Respiratory

In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.

Skin/Body

Protective work clothing

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Properties Status
---
Voc Content
---
Solubility In Water
Fully miscible.
Ph
1,1
Lower Explosive Limit
Not determined.
Colour Intensity
---
Vapor Pressure
23 hPa
Solidification Point
---
Explosive Limits
---
Flammability
Not applicable.
Solubility
---
Partition Coefficient
Not determined.
Physical State Data
liquid
Vapor Density
---
Dynamic Viscosity
Not determined.
Decomposition Temperature
Not determined.
State Under Standard Conditions
---
Solubility In Fat
---
Metal Corrosion
---
Bulk Density
---
Relative Density
---
Softening Point
---
Auto Ignition Temperature
400 °C
Odor
Odourless
Flash Point
Not applicable.
Freezing Point
---
Colour
Blue
Odor Threshold
Not determined.
Form
Liquid
Melting Point
Undetermined.
Relative Evaporation Rate
---
Physical State
Liquid
Crystallisation Point
---
Appearance
---
Upper Explosive Limit
Not determined.
Density
---
Cloud Point
---
Evaporation Rate
---
Boiling Point
Undetermined.
Molecular Weight
---
Kinematic Viscosity
Not determined.
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

No decomposition if used according to specifications.

Hazardous reactions

No dangerous reactions known.

Avoid

No further relevant information available.

Incompatible

No further relevant information available.

Decomposition

No dangerous decomposition products known.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN2796
Shipping Name
SULPHURIC ACID mixture
Transport Class
8
Packing Group
II
ADR

Warning: Corrosive substances.

IMDG

Warning: Corrosive substances.

IATA

Warning: Corrosive substances.

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for DiaMed HbF Screening Test Staining Solution?

The signal word is danger.

What is the physical form of DiaMed HbF Screening Test Staining Solution?

DiaMed HbF Screening Test Staining Solution is a liquid with blue color. It has odourless odor.

What is DiaMed HbF Screening Test Staining Solution used for?

In vitro diagnostic medical device or component.

What are the hazard statements for DiaMed HbF Screening Test Staining Solution?

This substance has 1 hazard statement:

  • H314: Causes severe skin burns and eye damage.

What is the melting point of DiaMed HbF Screening Test Staining Solution?

The melting point is Undetermined. and the boiling point is Undetermined..

Compliance Scanner

Scan your compliance