NextSDS Logo
Safety Data Sheet EN

ICAFLEX SK644

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
ICAFLEX SK644
Product Code
151162

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Adhesives, binding agents.

Manufacturers & Suppliers

I

ICAP-SIRA CHEMICALS AND POLYMERS S.P.A.

manufacturer

Via F.Corridoni 19 20015 Parabiago (MI) Italia

+39 0331 496111

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 2
Eye Irrit. Cat. 2
STOT SE Cat. 3

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

Hazard Statements

H225 Highly flammable liquid and vapour.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.

Precautionary Statements

P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P233 Keep container tightly closed.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P312 Call a POISON CENTER/ doctor/if you feel unwell.
P370 + P378 In case of fire: use dry powder, CO2, foam for extinction. Never use water.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
butanone; ethyl methyl ketone EC: 201-159-0 78-93-3 50 - 60% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove casualty to fresh air and keep warm and at rest.

Skin contact

Remove contaminated clothing immediately and dispose off safely. Wash thoroughly the body (shower or bath). After contact with skin, wash immediately with soap and plenty of water.

Eye contact

After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an ophthalmologist immediately. Protect uninjured eye.

Ingestion

Do not under any circumstances induce vomiting. OBTAIN A MEDICAL EXAMINATION IMMEDIATELY.

Immediate Medical Attention

In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible).

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

dry powder, CO2, foam

Unsuitable media

In case of fire of insoluble products / immiscible in water, the use of water, increase the risk of propagation of the area of fire.

Specific hazards

Burning produces heavy smoke. When heated (decomposition) or in case of fire may liberate carbon oxides, gases and vapors which are dangerous to health.

Instructions

Move undamaged containers from immediate hazard area if it can be done safely.

Firefighter Protection

Use suitable breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Remove persons to safety.

Environmental

Do not allow to enter into soil/subsoil. Do not allow to enter into surface water or drains.

Cleanup methods

Retain contaminated washing water and dispose it.

Materials: absorbing material, organic, sand

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with skin and eyes, inhalation of vapours and mists. Don't use empty container before they have been cleaned. Before making transfer operations, assure that there aren't any incompatible material residuals in the containers.

Storage

Store in sealed original container protected against moisture. Ensure good ventilation/extraction. Keep container tightly sealed and store in a frost free place. Store in a cool, dry place. Store at below 20 °C. Keep away from unguarded flame and heat sources. Avoid direct exposure to sunlight. Avoid accumulating electrostatic charge. Keep away from food, drink and feed.

Hygiene

Contamined clothing should be changed before entering eating areas. Do not eat or drink while working.

Fire prevention

Keep away from unguarded flame, sparks, and heat sources. Avoid direct exposure to sunlight. Avoid accumulating electrostatic charge.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Always provide good ventilation to maintain air contaminants below exposure limits (it is advisable to work under vacuum system). See also section 7 and section 13.

Hands

Suitable gloves type: Butyl caoutchouc (butyl rubber) - 0.6-0.8 mm

Eyes

Use close fitting safety goggles, don't use eye lens.

Respiratory

Use adequate protective respiratory equipment. Ensure good ventilation to maintain air contaminants below exposure limits. Use respiratory protection filters for gas / vapor (Type A / AX brown, ref. Standard EN 141) as a function of the levels of occupational exposure to chemical agents.

Skin/Body

Chemical protection clothing.

Environmental

See data PNEC. See also section 6.2 and 13.1. Prevent spills into public sewers or the immediate environment. Do not empty into drains; dispose of this material and its container at a collection point for hazardous waste and in accordance with local regulations. Refer to applicable national and Community legislation concerning environmental protection, waste water, soil pollution and integrated pollution prevention and control (ex. IPPC). Check whether the activity that uses the product falls within the scope of Directive 96/61/EC (IPPC). The emissions from ventilation or work process equipment should be checked to ensure compliance with the directives of the binding legislation on environmental protection. In some cases, to reduce emissions, might be needed maintenance or technical plant modifications.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
Liquid colorless
Colour
colorless
Colour Intensity
---
Form
---
Odor
solvent
Odor Threshold
0,74 (solvent) mg/m3
Ph
N.A.
Melting Point
< 0 °C
Boiling Point
80°C
Flash Point
-9 °C
Freezing Point
< 0 °C
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
n.d.
Vapor Pressure
N.A.
Vapor Density
n.d.
Relative Density
ca 1
Bulk Density
---
Density
---
Flammability
Not Relevant
Upper Explosive Limit
11.5 vol%
Lower Explosive Limit
1.8 vol%
Explosive Limits
---
Auto Ignition Temperature
505 °C
Decomposition Temperature
N.D.
Solubility
---
Partition Coefficient
n.d.
Solubility In Water
insoluble
Solubility In Fat
MISCIBLE IN ORGANIC DISSOLVENTS
Molecular Weight
---
Voc Content
---
Metal Corrosion
---
Dynamic Viscosity
16800 mPa.s (25°C)
Kinematic Viscosity
---
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions

Reactivity

Stable under normal conditions

Avoid

Stable under normal conditions.

Incompatible

Avoid contact with combustible materials. The product could catch fire.

Decomposition

None known. When heated (decomposition) or in case of fire may liberate carbon oxides, gases and vapors which are dangerous to health.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1866
Shipping Name
RESIN SOLUTION
Transport Class
3
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for ICAFLEX SK644?

The signal word is danger.

What is the physical form of ICAFLEX SK644?

ICAFLEX SK644 is a liquid appearing as liquid colorless with colorless color. It has solvent odor.

What is ICAFLEX SK644 used for?

Adhesives, binding agents.

What are the hazard statements for ICAFLEX SK644?

This substance has 3 hazard statements:

  • H225: Highly flammable liquid and vapour.
  • H319: Causes serious eye irritation.
  • H336: May cause drowsiness or dizziness.

What is the melting point of ICAFLEX SK644?

The melting point is < 0 °C and the boiling point is 80°C.