Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Lp-PLA2 FS Reagent R1
- Product Code
- 1 7181 XX XX XXX
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Reagent for in-vitro diagnostics in human samples
Uses advised against
For professional use only.
Manufacturers & Suppliers
DiaSys Diagnostic Systems GmbH
manufacturer
Alte Strasse 9, DE-65558 Holzheim
+49 (0) 6432-9146-0
http://www.diasys.de
Infraserv
+49 (0) 69-305-6418
Emergency Contacts
Infraserv
+49 (0) 69-305-6418
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Aqueous solution of inorganic salts and organic compounds.
The product does not contain dangerous substances above limits that need to be mentioned in this section according to applicable EU-legislation.
First Aid Measures
Emergency procedures for chemical exposure incidents
Provide fresh air. Seek medical treatment in case of troubles.
Symptoms: Respiratory tract irritation.
Remove residues with soap and water. Change contaminated clothing. In case of skin reactions, consult a physician.
Symptoms: Skin irritation.
Immediately flush eyes with plenty of flowing water for 10 to 15 minutes holding eyelids apart. Subsequently consult an ophthalmologist.
Symptoms: Eye irritation.
Rinse mouth and drink large quantities of water. Seek medical attention. Never give anything by mouth to an unconscious person.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Product is non-combustible. Extinguishing materials should therefore be selected according to surroundings.
Fires in the immediate vicinity may cause the development of dangerous vapours.
Firefighter Protection
In case of surrounding fires: Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid contact with skin and eyes.
Do not allow to penetrate into soil, waterbodies or drains.
Soak up with absorbent materials. Wash spill area with plenty of water.
Materials: sand, siliceus earth, acid- or universal binder
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with skin and eyes.
Keep containers tightly closed and at a temperature between 2 °C and 8 °C.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
When dust and vapours form: Withdraw by suction.
Protective gloves according to EN 374. Glove material: nitrile rubber, butyl caoutchouc (butyl rubber) or fluoro rubber. Breakthrough time: >480 min. Observe glove manufacturer's instructions concerning penetrability and breakthrough time.
Tightly sealed goggles according to EN 166.
Provide adequate ventilation.
Wear suitable protective clothing.
Refer to "6.2 Environmental precautions".
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
refer to 10.3
No hazardous reactions known.
Protect against heat /sun rays.
Strong acids and alkalis
No decomposition when used properly. Thermal decomposition: No data available
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Lp-PLA2 FS Reagent R1?
The signal word is no signal word.
What is the physical form of Lp-PLA2 FS Reagent R1?
Lp-PLA2 FS Reagent R1 is a liquid with clear, colourless color. It has no characteristic odour odor.
What is Lp-PLA2 FS Reagent R1 used for?
Reagent for in-vitro diagnostics in human samples