Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- di-Sodium hydrogen phosphate heptahydrate for analysis EMSURE® ACS
- Product Code
- 1.06575
- Chemical Name
- di-Sodium hydrogen phosphate heptahydrate
Regulatory Identifiers
- CAS Number
- 7782-85-6 Check regulations →
- REACH No.
- 01-2119489797-11-XXXX
Identified Uses
Reagent for analysis
Manufacturers & Suppliers
Sigma-Aldrich Chemie GmbH
manufacturer
Eschenstrasse 5, D-82024 TAUFKIRCHEN
+49 (0)89 6513-1130
Emergency Contacts
CHEMTREC Deutschland
0800 181 7059
CHEMTREC weltweit
+49 (0)696 43508409
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Na2HPO4 · 7H2O EC: 231-448-7 | 7782-85-6 | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
fresh air.
Take off immediately all contaminated clothing. Rinse skin with water/ shower.
rinse out with plenty of water. Remove contact lenses.
make victim drink water (two glasses at most). Consult doctor if feeling unwell.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
For this substance/mixture no limitations of extinguishing agents are given.
Not combustible. Fire may cause evolution of: Oxides of phosphorus. Ambient fire may liberate hazardous vapours.
Suppress (knock down) gases/vapors/mists with a water spray jet.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid inhalation of dusts. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up dry. Clean up affected area.
Related Products
Similar products with comparable safety profiles
Sodium dihydrogen phosphate monohydrate for analysis EMSURE® ACS, Reag. Ph Eur
CAS: 10049-21-5
di-Potassium hydrogen phosphate anhydrous for analysis EMSURE®
CAS: 7758-11-4
Tungstophosphoric acid hydrate for analysis EMSURE®
CAS: 12501-23-4
di-Sodium oxalate for analysis EMSURE®
CAS: 62-76-0
Potassium dihydrogen phosphate for analysis EMSURE® ISO
CAS: 7778-77-0
Sodium hydrogen carbonate for analysis EMSURE® ACS, Reag.Ph Eur
CAS: 144-55-8
di-Ammonium hydrogen citrate for analysis EMSURE® ACS,Reag. Ph Eur
---
Sodium acetate trihydrate for analysis EMSURE® ACS,ISO,Reag. Ph Eur
CAS: 6131-90-4
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For precautions see section 2.2.
Tightly closed. Dry. Recommended storage temperature see product label.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Required when dusts are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type P1. The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
No data available
Exothermic reaction with: Strong acids, antipyrine, Lead, acetates
Exposure to moisture.
No data available
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for di-Sodium hydrogen phosphate heptahydrate for analysis EMSURE® ACS?
The signal word is no signal word.
What is the physical form of di-Sodium hydrogen phosphate heptahydrate for analysis EMSURE® ACS?
di-Sodium hydrogen phosphate heptahydrate for analysis EMSURE® ACS is a solid with white color. It has no data available odor.
What is di-Sodium hydrogen phosphate heptahydrate for analysis EMSURE® ACS used for?
Reagent for analysis
What is the melting point of di-Sodium hydrogen phosphate heptahydrate for analysis EMSURE® ACS?
The melting point is No data available and the boiling point is No data available.