Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- di-Sodium hydrogen phosphate anhydrous for analysis particle size about 0.2-1 mm (~18-80 mesh ASTM) EMSURE®
- Product Code
- 1.06559
Regulatory Identifiers
- CAS Number
- 7558-79-4 Check regulations →
- REACH No.
- 01-2119489797-11-XXXX
Identified Uses
Reagent for analysis
Manufacturers & Suppliers
Millipore
manufacturer
Merck KGaA
manufacturer
Frankfurter Str. 250 D-64271 DARMSTADT
+49 (0)6151 72-0
Emergency Contacts
CHEMTREC (GB)
+(44)-870-8200418
CHEMTREC Ireland
+(353)-19014670
CHEMTREC India
001-803-017-9114
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Na2HPO4 EC: 231-448-7 | 7558-79-4 | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Not combustible. Fire may cause evolution of: Oxides of phosphorus. Ambient fire may liberate hazardous vapours.
Suppress (knock down) gases/vapors/mists with a water spray jet.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid inhalation of dusts. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up dry. Clean up affected area.
Related Products
Similar products with comparable safety profiles
di-Sodium hydrogen phosphate dihydrate for analysis EMSURE®
CAS: 10028-24-7
di-Sodium hydrogen phosphate heptahydrate for analysis EMSURE® ACS
CAS: 7782-85-6
di-Potassium hydrogen phosphate anhydrous for analysis EMSURE®
CAS: 7758-11-4
di-Potassium hydrogen phosphate trihydrate for analysis EMSURE®
CAS: 16788-57-1
Sodium dihydrogen phosphate monohydrate for analysis EMSURE® ACS,Reag. Ph Eur
CAS: 10049-21-5
Sodium dihydrogen phosphate monohydrate for analysis EMSURE® ACS, Reag. Ph Eur
CAS: 10049-21-5
tri-Sodium phosphate dodecahydrate for analysis EMSURE® ACS,Reag. Ph Eur
CAS: 10101-89-0
Potassium dihydrogen phosphate for analysis EMSURE® ISO
CAS: 7778-77-0
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For precautions see section 2.2.
Tightly closed. Dry. Recommended storage temperature see product label.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Respiratory protection is not required. Where protection from nuisance levels of dusts are desired, use type N95 (US) or type P1 (EN 143) dust masks. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
No data available
Exothermic reaction with: Strong acids, antipyrine, acetates
no information available
No data available
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for di-Sodium hydrogen phosphate anhydrous for analysis particle size about 0.2-1 mm (~18-80 mesh ASTM) EMSURE®?
The signal word is no signal word.
What is the physical form of di-Sodium hydrogen phosphate anhydrous for analysis particle size about 0.2-1 mm (~18-80 mesh ASTM) EMSURE®?
di-Sodium hydrogen phosphate anhydrous for analysis particle size about 0.2-1 mm (~18-80 mesh ASTM) EMSURE® is a solid appearing as form: solid color: white with white color. It has odorless odor.
What is di-Sodium hydrogen phosphate anhydrous for analysis particle size about 0.2-1 mm (~18-80 mesh ASTM) EMSURE® used for?
Reagent for analysis
What is the melting point of di-Sodium hydrogen phosphate anhydrous for analysis particle size about 0.2-1 mm (~18-80 mesh ASTM) EMSURE®?
The melting point is > 450 °C - Regulation (EC) No. 440/2008, Annex, A.1 and the boiling point is No data available.