Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- REFRACAST Nanobond F-70 AL
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Refractory lining for industrial applications.
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
Refratechnik Steel GmbH
manufacturer
Am Seestern 5, 40547 Düsseldorf
+49 211 58 58 0
Emergency Contacts
Dpt. Management systems
+ 49 171 8120436
during the regular office hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Refractory product based on fireclay
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| aluminium oxide EC: 215-691-6 | 1344-28-1 | 20 - 55% | No |
| clays, flint, calcined | 93821-35-3 | 20 - 55% | No |
| polypropylene | --- | 3% | No |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of inhalation of dust remove to fresh air. Drink water and blow nose.
After skin contact with the dust wash with plenty of warm water and soap.
After contact with dust flush open eyes with running water during several minutes. If the trouble persists seek medical advice.
After swallowing dust, rinse mouth and drink plenty of water.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use fire extinguishing methods suitable to surrounding conditions.
No further relevant information available.
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not allow to enter sewers/ surface or ground water.
Pick up mechanically, dust-free, e.g. by moistening with water
Related Products
Similar products with comparable safety profiles
REFRACAST Nanobond F-70 AL
---
REFRACAST Nanobond B-90 AL
---
REFRACAST Nanobond B-90 AL
---
REFRACAST Nanobond B-90 AL
---
LOCTITE ECCOBOND EN 3521F 70CC
---
BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER
---
Alu-Cast 80 HS
---
LOCTITE ECCOBOND F 114-R known as TRA-BOND F114-R
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Prevent formation of dust. Have ready for use an eye wash right next to the working place.
Do not store near to a fire or other heat sources. Store in dry conditions.
Have ready for use an eye wash right next to the working place.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
In case of work with machines (e.g. cutting and grinding machines) ensure extraction system or sufficient ventilation.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles. Face protection
Filter type P1 - P3, depending on the dust concentration. Respiratory protection for dust exposure
Tight-fitting protective work clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for REFRACAST Nanobond F-70 AL?
The signal word is no signal word.
What is the physical form of REFRACAST Nanobond F-70 AL?
REFRACAST Nanobond F-70 AL is a solid with light grey color. It has specific type odor.
What is REFRACAST Nanobond F-70 AL used for?
Refractory lining for industrial applications.
What is the melting point of REFRACAST Nanobond F-70 AL?
The melting point is Undetermined. and the boiling point is Undetermined..