Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ALUMINIUM PUTTY (F) RESIN
- Product Code
- X0002
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Resin.
Manufacturers & Suppliers
ITW Performance Polymers
Bay 150, Shannon Industrial Estate, Co. Clare, Ireland, V14 DF82
353(61)771500
Emergency Contacts
Emergency Contact
+44(0)1235 239 670
24h
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| EPOXY RESIN (Number average MW <= 700 ) EC: 500-033-5 | 25068-38-6 | 30 - 60% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move affected person to fresh air at once. Get medical attention if any discomfort continues.
Remove affected person from source of contamination. Wash skin thoroughly with soap and water. Get medical attention if irritation persists after washing.
Remove any contact lenses and open eyelids wide apart. Continue to rinse for at least 15 minutes. Get medical attention if irritation persists after washing.
Rinse mouth thoroughly with water. Do not induce vomiting. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention.
Immediate Medical Attention
Get medical attention if any discomfort continues, if irritation persists after washing, or if ingested.
Medical Treatment
No specific recommendations.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Extinguish with foam, carbon dioxide or dry powder.
Irritating gases or vapours.
Avoid breathing fire gases or vapours. Keep up-wind to avoid fumes.
Firefighter Protection
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid contact with skin and eyes. Wear protective clothing as described in Section 8 of this safety data sheet.
Avoid the spillage or runoff entering drains, sewers or watercourses.
Collect and place in suitable waste disposal containers and seal securely.
Materials: suitable waste disposal containers
Related Products
Similar products with comparable safety profiles
PLASTIC STEEL PUTTY(A) RESIN
---
ALUMINIUM RESISTANT CASTABLE
---
ALUMINIUM PASTE WITH WHITE SPIRIT
CAS: 7429-90-5, 67701-06-8
ALUMINIUM RESISTANT COATING MATERIAL
---
DEVCON® Plastic Steel® Putty (A) Resin
---
STAPA 4 n.l. Aluminium Paste
---
SILVERSHINE 412 Aluminium Paste
---
GG440/880 n.l. Aluminium Paste
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only in well-ventilated areas. Handle and open container with care. Keep away from heat, sparks and open flame. Avoid contact with skin and eyes.
Store in tightly-closed, original container in a dry, cool and well-ventilated place.
Do not eat, drink or smoke when using the product. Good personal hygiene procedures should be implemented.
Keep away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate general and local exhaust ventilation.
Wear protective gloves made of the following material: Rubber or plastic. To protect hands from chemicals, gloves should comply with European Standard EN374. The selected gloves should have a breakthrough time of at least 8 hours.
Eyewear complying with an approved standard should be worn if a risk assessment indicates eye contact is possible. The following protection should be worn: Chemical splash goggles. Personal protective equipment for eye and face protection should comply with European Standard EN166.
If ventilation is inadequate, suitable respiratory protection must be worn. Respirator selection must be based on exposure levels, the hazards of the product and the safe working limits of the selected respirator. Check that the respirator fits tightly and the filter is changed regularly. Wear a respirator fitted with the following cartridge: Gas filter, type A2. Half mask and quarter mask respirators with replaceable filter cartridges should comply with European Standard EN140.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal ambient temperatures and when used as recommended.
Strong oxidising agents. Acids. Amines.
Not available.
Avoid heat, flames and other sources of ignition.
Strong oxidising agents. Strong acids. Amines.
Oxides of carbon. Thermal decomposition or combustion may liberate carbon oxides and other toxic gases or vapours. Vapours/gases/fumes of: Aldehydes.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3082
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (EPOXY RESIN (Number average MW <= 700))
- Transport Class
- 9
- Packing Group
- III
Emergency Action Code •3Z
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ALUMINIUM PUTTY (F) RESIN?
The signal word is warning.
What is the physical form of ALUMINIUM PUTTY (F) RESIN?
ALUMINIUM PUTTY (F) RESIN is a liquid appearing as paste. with grey. color. It has slight. odor.
What is ALUMINIUM PUTTY (F) RESIN used for?
Resin.
What are the hazard statements for ALUMINIUM PUTTY (F) RESIN?
This substance has 4 hazard statements:
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H411: Toxic to aquatic life with long lasting effects.
What is the melting point of ALUMINIUM PUTTY (F) RESIN?
The melting point is n/d°C and the boiling point is >260°C.