Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Lacomit stopping-off Lacquer
- Product Code
- AGG371
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Epoxy resin hardener for use in microscopy.
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
Agar Scientific, Elektron Technology UK Ltd
manufacturer
Parsonage Lane, Stansted CM24 8GF, United Kingdom
+44 (0) 1279 813 519
Emergency Contacts
Emergency Contact
+44 (0)1856 407333
24 hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS05
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| xylene EC: 215-535-7 | 1330-20-7 | 45% | Yes |
| butan-1-ol EC: 200-751-6 | 71-36-3 | 20% | Yes |
| n-butyl acetate EC: 204-658-1 | 123-86-4 | 20% | Yes |
| acetone EC: 200-662-2 | 67-64-1 | 5% | Yes |
| 1-methoxy-2-propanol EC: 203-539-1 | 107-98-2 | 5% | Yes |
| Amine, Kolophonium-, Verbindungen mit 9-(2-Carboxyphenyl)-3,6-bis(diethylamino)xanthylliumchlorid und Dinatriumhydrogenbis(4-(4,5-dihydro-3-methyl-5-oxo-1-phenyl-1H-pyrazol-4-yl)azo)-3-hydroxy-1-naphthalinsulfonato(3-))chromat(3-) EC: 308-114-5 | 97862-65-2 | 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist. In case of unconsciousness place patient stably in side position for transportation.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water.
If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, sand, extinguishing powder.
Water, Water with full jet
Advice for firefighters
Firefighter Protection
Protective equipment: Mouth respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away.
Do not allow to enter sewers/ surface or ground water.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Keep container tightly sealed.
Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable if used according to specifications.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1263
- Shipping Name
- PAINT, solution
- Transport Class
- 3
- Packing Group
- III
Warning: Flammable liquids.
Warning: Flammable liquids.
Warning: Flammable liquids.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Lacomit stopping-off Lacquer?
The signal word is danger.
What is the physical form of Lacomit stopping-off Lacquer?
Lacomit stopping-off Lacquer is a liquid with according to product specification color. It has characteristic odor.
What is Lacomit stopping-off Lacquer used for?
Epoxy resin hardener for use in microscopy.
What are the hazard statements for Lacomit stopping-off Lacquer?
This substance has 4 hazard statements:
- H226: Flammable liquid and vapour.
- H315: Causes skin irritation.
- H318: Causes serious eye damage.
- H335: May cause respiratory irritation. May cause drowsiness or dizziness.
What is the melting point of Lacomit stopping-off Lacquer?
The melting point is Undetermined. and the boiling point is 137 °C.