Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE LIOFOL HS 2809-22 RE 50KG
- Product Code
- 2938282
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Heat seal coating
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air.
Wash affected area immediately with soap and water. Remove contaminated clothing and footwear.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.
If material is ingested, immediately contact a physician or poison control center. DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
If material is ingested, immediately contact a physician or poison control center.
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures appropriate to local circumstances and the surrounding environment.
Not available.
This product is an aqueous mixture which will not burn. If evaporated to dryness, the solid residue may pose a slight fire hazard. Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.
Keep unnecessary personnel away.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Small spills can be absorbed with vermiculite, clay or other suitable non-biodegradable absorbent material, scooped up and placed in containers.
For large spills dike ahead and collect liquid.
Prevent further leakage or spillage if safe to do so.
Small spills can be absorbed with vermiculite, clay or other suitable non-biodegradable absorbent material, scooped up and placed in containers. For large spills dike ahead and collect liquid.
Materials: vermiculite, clay or other suitable non-biodegradable absorbent material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wash thoroughly after handling. Use only with adequate ventilation. Avoid contact with eyes, skin and clothing. Do not taste or swallow. Keep container closed. Do not breathe gas/fumes/vapor/spray.
Keep the container tightly closed and in a cool, well-ventilated place. Protect from freezing.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Work should be done in an adequately ventilated area (i.e., ventilation sufficient to maintain concentrations below one half of the PEL and other relevant standards). Local exhaust ventilation is recommended when general ventilation is not sufficient to control airborne contamination.
Use impermeable gloves
Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists.
Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Observe OSHA regulations for respirator use (29 CFR 1910.134).
protective clothing as necessary to prevent skin contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
Will not occur.
Freezing conditions.
Avoid contact with materials that are water reactive.
Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Thermal decomposition can lead to release of irritating gases and vapors.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE LIOFOL HS 2809-22 RE 50KG?
The signal word is no signal word.
What is the physical form of LOCTITE LIOFOL HS 2809-22 RE 50KG?
LOCTITE LIOFOL HS 2809-22 RE 50KG is a liquid with white color. It has specific odor.
What is the solubility of LOCTITE LIOFOL HS 2809-22 RE 50KG?
Miscible Water
What is LOCTITE LIOFOL HS 2809-22 RE 50KG used for?
Heat seal coating
What is the melting point of LOCTITE LIOFOL HS 2809-22 RE 50KG?
The melting point is Not applicable, Product is a liquid and the boiling point is 100 °C (212°F).