Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- SINMAST P 103 B' Comp.
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Curing agent for epoxy resin
Manufacturers & Suppliers
SINTECNO SA
manufacturer
4, Anaxagora str., P.O.Box 202, PC 194 00, Koropi, Attica, GREECE
0030 210 6026020
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. Then consult a doctor.
Drink plenty of water and provide fresh air. Call a doctor immediately.
Immediate Medical Attention
Call a doctor immediately if swallowed, consult a doctor for eye contact, call for a doctor for inhalation.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO₂, powder or water spray. Fight larger fires with spray water.
Water with full jet
Formation of toxic gases is possible during heating or in case of fire
Firefighter Protection
Wear self-contained respiratory protective device
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away
Prevent seepage into sewage system, work pits and cellars. Inform respective authorities in case of seepage into water course or sewage system. Do not allow to enter sewers / surface or ground water.
Absorb with liquid binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation / exhaustion at the workplace. Prevent formation of aerosols.
Store in cool location. Provide ventilation for receptacles. Protect from heat and direct sunlight. Keep container tightly sealed.
Protect from heat. Protect against electrostatic charges
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data, see item 7
Protective gloves. The glove material has to be impermeable and resistant to the product / the substance / the preparation. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
Use suitable respiratory protective device in case of insufficient ventilation
Protective work clothing and boots.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used and stored according to specifications
Reacts with strong acids and oxidizing agents
No further relevant information available
No further relevant information available
Carbon monoxide and carbon dioxide
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 2735
- Shipping Name
- amines, liquid, corrosive, N.O.S. mixture
- Transport Class
- 8
- Packing Group
- III
Warning : corrosive substances
Warning : corrosive substances
Warning : corrosive substances
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for SINMAST P 103 B' Comp.?
The signal word is danger.
What is the physical form of SINMAST P 103 B' Comp.?
SINMAST P 103 B' Comp. is a paste appearing as paste with black color. It has ammonia like odor.
What is SINMAST P 103 B' Comp. used for?
Curing agent for epoxy resin
What are the hazard statements for SINMAST P 103 B' Comp.?
This substance has 5 hazard statements:
- H302: Harmful if swallowed
- H312: Harmful in contact with skin
- H314: Causes severe skin burns and eye damage
- H317: May cause an allergic skin reaction
- H412: Harmful to aquatic life with long lasting effects
What is the melting point of SINMAST P 103 B' Comp.?
The melting point is Undetermined .