PRODUCT 116.74D

Remove exposed person to fresh air if adverse effects are observed.

Take off contaminated clothing and wash before re-use. Wash skin thoroughly with soap and water. If skin irritation occurs, get medical attention.

Rinse cautiously with water for several minutes. Flush thoroughly with water. If irritation occurs, get medical assistance. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.

Rinse mouth. Get medical attention if symptoms occur.

CO2, Dry chemical or Foam. Water can be used to cool and protect exposed material.

Do not use water jet as an extinguisher, as this will spread the fire.

Vapors may cause a flash fire or ignite explosively. Prevent buildup of vapors or gases to explosive concentrations. Vapors may travel considerable distance to a source of ignition and flash back. Water may cause splattering. Container may rupture on heating. Material creates a special hazard because it floats on water. See section 10 for additional information.

No data available.

ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area). Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Keep unauthorized personnel away.

Dike far ahead of larger spill for later recovery and disposal.

Do not contaminate water sources or sewer. Prevent further leakage or spillage if safe to do so.

Pick up free liquid for recycle and/or disposal. Residual liquid can be absorbed on inert material.

Materials: inert material

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Avoid contact with skin. Avoid contact with eyes. Observe good industrial hygiene practices. Provide adequate ventilation. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Launder contaminated clothing before reuse.

Store in containers made of same material as original container. Keep cool. Store in a well-ventilated place.

Observe good industrial hygiene practices. Wash hands thoroughly after handling. Launder contaminated clothing before reuse.

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Always transfer product by means which avoid static buildup.

No special requirements under ordinary conditions of use and with adequate ventilation. Adequate ventilation should be provided so that exposure limits are not exceeded. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits.

Use nitrile or neoprene gloves. Use good industrial hygiene practices. In case of skin contact, wash hands and arms with soap and water. Chemical resistant gloves. For typical use and handling of chemical substances, gloves should meet the standards set out in EN 374. For continuous contact, we suggest gloves with a minimum breakthrough time of 240 minutes, or > 480 minutes if suitable gloves can be obtained. For general applications, we recommend gloves with a thickness typically greater than 0.35 mm.

Wear tight-fitting goggles or face shield. Safety glasses. If potential for splash or mist exists, wear chemical goggles or faceshield. Eye protection should meet the standards set out in EN 166.

Use respirator with an organic vapor and dust/mist cartridge if the recommended exposure limit is exceeded. Use self-contained breathing apparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites. Use respirator with a combination organic vapor and dust/mist cartridge. Respiratory Protective Equipment (RPE) is not normally required where there is adequate natural or local exhaust ventilation to control exposure. In case of insufficient ventilation, wear suitable respiratory equipment.

Wear apron or protective clothing in case of contact. Do not wear rings, watches or similar apparel that could entrap the material. Gloves, coveralls, apron, boots as necessary to minimize contact.

No data available. See section 6 for details.

Material is stable under normal conditions.

No data available.

Will not occur.

Heat, sparks, flames. Excessive heat. Contact with acids. Strong caustic agents.

Strong acids. Lead and lead alloys Oxidizing agents, Reactive metals, Sodium or Calcium Hypochlorite. Materials reactive with hydroxyl compounds.

Thermal decomposition or combustion may generate smoke, carbon monoxide, carbon dioxide, and other products of incomplete combustion.

Treatment, storage, transportation, and disposal must be in accordance with applicable Federal, State/Provincial, and Local regulations.

Dispose of packaging or containers in accordance with local, regional, national and international regulations.