NEONATAL Biotinidase Screening Assay

Move to fresh air. Call a physician. If breathing is difficult, supply oxygen.

Take off immediately all contaminated clothing. Rinse skin with water/shower. For specific reagents: wash abundantly with soap and water, rinse thoroughly, and disinfect with a 1/10 dilution of 12% liquid bleach. Leave the disinfectant in contact for 5 minutes. Consult a hospital emergency medical department immediately.

Rinse immediately with plenty of water, keeping the eyelids wide open for at least 15 minutes. Remove contact lenses. Call in ophthalmologist or doctor immediately.

Make victim drink water (two glasses at most). Do not induce vomiting (risk of perforation). Do not attempt to neutralise. Consult a physician or hospital emergency medical department immediately.

Boric acid: Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Sulfuric acid: Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Trichloroacetic acid: Water, Foam, Carbon dioxide (CO2), Dry powder.

For this substance/mixture no limitations of extinguishing agents are given.

Borane/boron oxides, Sulfur oxides, Carbon oxides, Hydrogen chloride gas. Fire may cause evolution of boron compounds, sulfur oxides, and hazardous combustion gases or vapours.

Suppress (knock down) gases / vapors / mists with a water spray jet.

Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.

Do not let product enter drains.

Take up carefully. Dispose of properly. Clean up affected area. Take up with liquid-absorbent and neutralising material (e.g. Chemizorb® H⁺, Merck Art. No. 101595).

Materials: liquid-absorbent and neutralising material (e.g. Chemizorb® H⁺, Merck Art. No. 101595)

Work under hood. Do not inhale substance/mixture.

Tightly closed. Dry. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorized persons. No metal containers.

Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

Boric acid: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Sulfuric acid: Full contact: Viton®, Minimum layer thickness: 0,7 mm, Break through time: 480 min, Material tested: Vitoject® (KCL 890 / Aldrich Z677698, Size M); Splash contact: butyl-rubber, Minimum layer thickness: 0,7 mm, Break through time: 120 min, Material tested: Butoject® (KCL 898). Trichloroacetic acid: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L.

Boric acid: Safety glasses (tested and approved under NIOSH (US) or EN 166(EU)). Sulfuric acid: Tightly fitting safety goggles (tested and approved under NIOSH (US) or EN 166(EU)). Trichloroacetic acid: Tightly fitting safety goggles (tested and approved under NIOSH (US) or EN 166(EU)).

Boric acid: Required when dusts are generated, Filter type P3. Sulfuric acid: Required when vapours/aerosols are generated, Filter B-(P2). Trichloroacetic acid: Filter type B. Standards: DIN EN 143, DIN 14387 and other accompanying standards.

Boric acid: Protective clothing. Sulfuric acid: Acid-resistant protective clothing. Trichloroacetic acid: Acid-resistant protective clothing.

Do not let product enter drains.

The products are chemically stable under standard ambient conditions (room temperature).

Boric acid (CAS-No: 10043-35-3): No data available; Sulfuric acid (CAS-No: 7664-93-9): Has a corrosive effect Strong oxidising agent; Tricholoracetic acid (CAS No: 76-03-9): The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.

Boric acid: Risk of explosion with: Acetic anhydride; Violent reactions possible with: Strong oxidising agents, Bases. Sulfuric acid: A risk of explosion and/or of toxic gas formation exists with the following substances: Alkali metals, Alkali compounds, Ammonia, Aldehydes, Acetonitrile, Alkaline earth metals, Alkalines, Acids, Alkaline earth compounds, Metals, Metal alloys, Oxides of phosphorus, Phosphorus, Hydrides, Halogen-halogen compounds, Oxyhalogenic compounds, Permanganates, nitrates, Carbides, Combustible substances, Organic solvent, Acetylidene, Nitriles, Organic nitro compounds, Anilines, Peroxides, Picrates, Nitrides, Lithium silicide, Iron(III) compounds, Bromates, Chlorates, Amines, Perchlorates, Hydrogen peroxide. Trichloroacetic acid: Risk of explosion with: Silver salt; Exothermic reaction with: alkalines, alkali hydroxides, Amines, Strong oxidizing agents, sulfoxides, dimethyl sulfoxide with Copper.

Boric acid: no information available; Sulfuric acid: no information available; Tricholoracetic acid: Exposure to moisture, Heat.

Boric acid: Potassium, Acid anhydrides; Sulfuric acid: Animal/vegetable tissues, Metals (Contact with metals liberates hydrogen gas); Trichloroacetic acid: Metals

In the event of fire: see section 5.

See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.

No data available for Boric acid (CAS-No: 10043-35-3)