NEONATAL GAL-T Screening Fluo

Fresh air. Call a physician.

Take off immediately all contaminated clothing. Rinse skin with water / shower. Call a physician immediately.

Rinse out with plenty of water. Remove contact lenses. Immediately call an ophthalmologist.

If swallowed: give water to drink (two glasses at most), avoid vomiting (risk of perforation). Call a physician immediately. Do not attempt to neutralise.

Water, Foam, Carbon dioxide (CO2), Dry powder

For this substance no limitations of extinguishing agents are given.

ProClin™ 300: Carbon oxides, Nitrogen oxides (NOx), Sulfur oxides, Hydrogen chloride gas, Combustible, Vapors are heavier than air and may spread along floors, Forms explosive mixtures with air on intense heating, Development of hazardous combustion gases or vapours possible in the event of fire. G6PDH: Nature of decomposition products not known, Combustible, Development of hazardous combustion gases or vapours possible in the event of fire.

Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.

Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert. Avoid inhalation of dusts.

Do not let product enter drains.

Take up carefully. Clean up affected area.

ProClin™ 300: Work under hood. Do not inhale substance/mixture. Avoid generation of vapours/aerosols. G6PDH: Work under hood. Do not inhale substance/mixture.

ProClin™ 300: Tightly closed. G6PDH: Tightly closed. Dry. Keep locked up or in an area accessible only to qualified or authorized persons.

Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

ProClin™ 300: Full contact: Material: butyl-rubber, Minimum layer thickness: 0,3 mm, Break through time: 480 min, Material tested: Butoject® (KCL 897 / Aldrich Z677647, Size M). Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 60 min, Material tested: Dermatril® (KCL 740 / Aldrich Z677272, Size M). G6PDH: Full contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L.

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Tightly fitting safety goggles

ProClin™ 300: Required when vapours/aerosols are generated. Recommended Filter type: Filter type ABEK. G6PDH: Required when dusts are generated. Recommended Filter type: Filter type P2. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.

Protective clothing

Do not let product enter drains.

The products are chemically stable under standard ambient conditions (room temperature).

ProClin™ 300: Forms explosive mixtures with air on intense heating. A range from approx. 15 Kelvin below the flash point is to be rated as critical. G6PDH: The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.

No data available

Strong heating

ProClin™ 300: Strong oxidizing agents, Reducing agents, Amines, Mercaptans; G6PDH: No data available

In the event of fire: see section 5.

Product Disposal recommendations are based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal.