Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Antifoam S3
- Product Form
- Antifoam
- Product Code
- 0810
- Chemical Name
- Preparation based on mineral oil and additives
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Antifoam
Manufacturers & Suppliers
D.A. Stuart Ltd.
manufacturer
Lincoln Street, Wolverhampton, West Midlands WV10 0DZ
+44 (0)1902 877600
Emergency Contacts
Emergency Contact
+44 (0)870 242 4434
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Chemical nature of the preparation
For the full text of the R phrases mentioned in this Section, see Section 16
First Aid Measures
Emergency procedures for chemical exposure incidents
Health injuries are not known or expected under normal use.
Wash off immediately with soap and plenty of water removing all contaminated clothes and shoes. If skin irritation persists, call a physician.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. If symptoms persist, call a physician.
Do not induce vomiting. If conscious, drink plenty of water. Call a physician immediately.
Immediate Medical Attention
Call a physician immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
dry chemical, foam, carbon dioxide (CO2).
Thermal decomposition can lead to release of irritating gases and vapours.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Sweep-up to prevent slipping hazard.
Prevent further leakage or spillage if safe to do so.
Absorb spill with inert material (e.g. dry sand or earth), then place in a chemical waste container.
Materials: inert material (e.g. dry sand or earth)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Handle in accordance with good industrial hygiene and safety practice. Avoid contact with skin, eyes and clothing.
Store in original container. Keep away from open flames, hot surfaces and sources of ignition. Do not freeze.
Handle in accordance with good industrial hygiene and safety practice.
Keep away from open flames, hot surfaces and sources of ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
not applicable.
if needed: safety gloves made of suitable material (e.g. nitril rubber; follow manufacturers' instructions and note CEN-symbol). Break through time: level 6, > 480 min, thickness 0,9 - 1,0 mm; CE-certified according to EN 374 cat. III.
If splashes are likely to occur, wear, safety glasses with side-shields
No personal respiratory protective equipment normally required
Usual safety precautions while handling the product will provide adequate protection against this potential effect.
Prevent product from entering drains. Local authorities should be advised if significant spillages cannot be contained.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions
Hazardous polymerisation does not occur.
Direct sources of heat. Extremes of temperature and direct sunlight. Do not freeze.
strong oxidising agents.
Thermal decomposition can lead to release of irritating gases and vapours.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Consult a licensed waste disposal company.
Dispose of in accordance with local regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- not regulated
- Shipping Name
- not regulated
- Transport Class
- not applicable
- Packing Group
- not regulated
Regulatory Information
Chemical regulations, safety assessments, and compliance status
In accordance with the EC-criteria, the product is classified as: Indication of danger: None.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Antifoam S3?
The signal word is no signal word.
What is the physical form of Antifoam S3?
Antifoam S3 is a liquid appearing as liquid with colourless color. It has bland odor.
What is the solubility of Antifoam S3?
insoluble
What is Antifoam S3 used for?
Antifoam