Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Rustlick™ Sump-Side Defoamer
- Product Code
- 78640
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Tank side additive for foam control
Uses advised against
None known.
Manufacturers & Suppliers
ITW Pro Brands
manufacturer
4647 Hugh Howell Rd Tucker, GA 30084 United States
1-800-241-8334 / 770-243-8800
http://www.lpslabs.com
Emergency Contacts
Chemtrec
1-800-424-9300
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
The manufacturer lists no ingredients as hazardous to health according to OSHA 29 CFR 1910.1200.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. Call a physician if symptoms develop or persist.
Wash off with soap and water. Get medical attention if irritation develops and persists.
Rinse with water. Get medical attention if irritation develops and persists.
Symptoms: Direct contact with eyes may cause temporary irritation.
Rinse mouth. Get medical attention if symptoms occur.
Immediate Medical Attention
Get medical attention if symptoms occur/develop/persist.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Do not use water jet as an extinguisher, as this will spread the fire.
During fire, gases hazardous to health may be formed.
Move containers from fire area if you can do so without risk. Use standard firefighting procedures and consider the hazards of other involved materials.
Firefighter Protection
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unnecessary personnel away.
Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.
Avoid discharge into drains, water courses or onto the ground.
Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Materials: vermiculite, dry sand, earth, absorbent material (e.g. cloth, fleece)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Do not get in eyes, on skin, or on clothing. Avoid prolonged exposure.
Store in tightly closed container.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Good general ventilation should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.
Wear suitable protective clothing.
Wear safety glasses with side shields (or goggles).
In case of insufficient ventilation, wear suitable respiratory equipment.
Wear appropriate chemical resistant gloves.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Material is stable under normal conditions.
The product is stable and non-reactive under normal conditions of use, storage and transport.
No dangerous reaction known under conditions of normal use.
Avoid temperatures exceeding the decomposition temperature. Contact with incompatible materials.
Strong oxidizing agents.
Carbon oxides.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Rustlick™ Sump-Side Defoamer?
The signal word is no signal word.
What is the physical form of Rustlick™ Sump-Side Defoamer?
Rustlick™ Sump-Side Defoamer is a liquid. appearing as opaque. white. with opaque. white. color. It has mild. odor.
What is Rustlick™ Sump-Side Defoamer used for?
Tank side additive for foam control
What are the hazard statements for Rustlick™ Sump-Side Defoamer?
This substance has 1 hazard statement:
- The mixture does not meet the criteria for classification.
What is the melting point of Rustlick™ Sump-Side Defoamer?
The melting point is Not available. and the boiling point is >212 °F (>100 °C).