Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Lysis Solution RL
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Laboratory chemicals
Uses advised against
No further information available.
Manufacturers & Suppliers
AJ Innuscreen GmbH
manufacturer
Biotechnologie Campus Berlin-Buch, Robert-Rössle-Straße 10, 13125 Berlin, Germany
+49 (0) 30 9489-3380
www.aj-innuscreen.de
Emergency Contacts
Poison Information Center / Vergiftungs-Informations-Zentrale
+49 (0) 761 19 240
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| guanidinium thiocyanate EC: 209-812-1 | 593-84-0 | 25 - 50% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly. Call a doctor immediately.
Rinse opened eye for several minutes under running water. Call a doctor immediately.
Call a doctor immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Water with full jet
Formation of toxic gases is possible during heating or in case of fire.
Firefighter Protection
Do not inhale explosion gases or combustion gases.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not allow product to reach sewage system or any water course.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace.
Store in cool, dry place in tightly closed receptacles. Store only in the original receptacle. Keep container tightly sealed. Store receptacle in a well ventilated area.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Additional information about design of technical facilities: No further data; see item 7.
Protective gloves. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
Use suitable respiratory protective device in case of insufficient ventilation.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
Contact with acids releases toxic gases.
No further relevant information available.
No further relevant information available.
Poisonous gases/vapours, Carbon monoxide and carbon dioxide
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Must not be disposed together with household garbage.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1760
- Shipping Name
- CORROSIVE LIQUID, N.O.S. (Guanidinium thiocyanate)
- Transport Class
- 8
- Packing Group
- III
Warning: Corrosive substances.
Warning: Corrosive substances.
Warning: Corrosive substances.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
No further relevant information available.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Lysis Solution RL?
The signal word is danger.
What is the physical form of Lysis Solution RL?
Lysis Solution RL is a fluid appearing as clear with clear color. It has characteristic odor.
What is Lysis Solution RL used for?
Laboratory chemicals
What are the hazard statements for Lysis Solution RL?
This substance has 3 hazard statements:
- H302: Harmful if swallowed.
- H314: Causes severe skin burns and eye damage.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of Lysis Solution RL?
The melting point is Undetermined. and the boiling point is 100 °C.