Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MasterFinish RL 211
- Product Code
- 000000000050380487
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Product for construction chemicals
Manufacturers & Suppliers
MB Solutions Australia Pty Ltd
manufacturer
11 Stanton Road, Seven Hills NSW 2147
+611300227300
Emergency Contacts
ChemTel
+1-813-248-0585
Australia
1-300-954-583
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Emulsion based on: vegetable oils in water
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Rapeseed oil | 8002-13-9 | 10% | No |
| beta.-Alanine, N-coco alkyl derivs. | 84812-94-2 | 0.025 - 0.25% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Keep patient calm, remove to fresh air. If symptoms persist, seek medical advice.
Immediately remove contaminated clothing. After contact with skin, wash immediately with plenty of water and soap. Under no circumstances should organic solvent be used. If irritation develops, seek medical attention.
Wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye specialist.
Immediately rinse mouth and then drink 200-300 ml of water, seek medical attention. Do not induce vomiting unless told to by a poison control center or doctor.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, Water spray, Dry powder, Carbon dioxide (CO2)
water jet
If exposed to fire, keep containers cool by spraying with water.
Firefighter Protection
Wear a self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray. Handle in accordance with good building materials hygiene and safety practice.
Contain contaminated water/firefighting water. Do not discharge into drains/surface waters/groundwater.
Pick up with suitable appliance and dispose of.
Related Products
Similar products with comparable safety profiles
MasterFinish RL 211 also RHEOFINISH 211
---
FARECLA G10 FINISHING COMPOUND
---
PS 1500 Finish Control
---
GMF3041 GLIDDEN MAX-FLEX INTERIOR/EXTERIOR TOPCOAT MATTE CLEAR
---
3M™ Finesse-It™ Polish - Final Finish
---
Finish - R
---
TECHNOMELT PUR PRIMER 6B-23
UFI: SF6K-AWX7-M20Q-K32Y
MR® 79 Special Cleaner
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Smoking, eating and drinking should be prohibited in the application area.
Keep only in the original container in a cool, dry, well-ventilated place away from ignition sources, heat or flame. Protect from direct sunlight.
When using, do not eat, drink or smoke. Hands and/or face should be washed before breaks and at the end of the shift. At the end of the shift the skin should be cleaned and skin-care agents applied. Gloves must be inspected regularly and prior to each use. Replace if necessary (e.g. pinhole leaks).
Normal measures for preventive fire protection.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ventilation systems to ensure adequate ventilation.
impermeable gloves Synthetic rubber gloves Manufacturer's directions for use should be observed because of great diversity of types.
Safety glasses with side-shields (frame goggles) (e.g. EN 166)
Wear respiratory protection if ventilation is inadequate. Combination filter for gases/vapours of organic, inorganic, acid inorganic and alkaline compounds (e.g. EN 14387 Type ABEK).
Body protection must be chosen based on level of activity and exposure.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if stored and applied as directed.
No decomposition if stored and applied as directed.
Stable under recommended storage conditions. No hazards to be specially mentioned.
See SDS section 7 - Handling and storage.
Strong acids, Strong bases, Strong oxidizing agents, Strong reducing agents
No hazardous decomposition products if stored and handled as prescribed/indicated.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Residues should be disposed of in the same manner as the substance/product.
Observe national and local legal requirements.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Not applicable
- Shipping Name
- Not applicable
- Transport Class
- Not applicable
- Packing Group
- Not applicable
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP): Not Scheduled. There is no applicable prohibition, authorisation and restricted use requirements, including for carcinogens referred to in Schedule 10 of the model WHS Act and Regulations.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MasterFinish RL 211?
The signal word is no signal word.
What is the physical form of MasterFinish RL 211?
MasterFinish RL 211 is a liquid appearing as liquid with white color. It has mild odor.
What is MasterFinish RL 211 used for?
Product for construction chemicals
What is the melting point of MasterFinish RL 211?
The melting point is approx. -4 °C and the boiling point is > 100 °C.