Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- RÖSLER Keramo-Finish® Compound RSP 506 S
- Product Code
- 04822005062
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Process auxiliary for surface finishing, Industrial use
Manufacturers & Suppliers
Rösler Oberflächentechnik GmbH
manufacturer
Hausen 1, D-96231 Bad Staffelstein
+49/9533/924-0
http://www.rosler.com
Rösler Metal Finishing USA, L.L.C.
distributor
1551 Denso Road, Battle Creek, MI 49037, USA
+1(269)441-3000
http://www.rosler.us
Emergency Contacts
CHEMTREC
(800)-424-9300
24h emergency contact
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| aluminium oxide | 1344-28-1 | 50 - 100% | Yes |
| Poly(oxy-1,2-ethanediyl), α-[(9Z)-2-[(1-oxo-9-octadecen-1-yl)amino]ethyl]-ω-hydroxy- | 26027-37-2 | 1 - 5% | Yes |
| Reaction product of benzenesulfonic acid, 4-C10-13-sec-alkyl derivs. and benzenesulfonic acid, 4-methyl- and sodium hydroxide | --- | 1 - 5% | Yes |
| potassium (Z)-oleate | 143-18-0 | 1 - 5% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Rinse out mouth with plenty of water. Do not induce vomiting; immediately call for medical help.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Water with full jet
No further relevant information available.
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away.
Do not allow product to enter sewers/ surface or ground water.
Pick up mechanically.
Related Products
Similar products with comparable safety profiles
MasterFinish RL 211 also RHEOFINISH 211
---
FARECLA G10 FINISHING COMPOUND
---
MasterFinish RL 211
---
Remint Polishing Compound H
---
Rösler Alu-Cast RAC-R
---
ROHPER +LSPR 6PK GLOSS ALMOND
---
ARCOL® POLYOL F-3040
---
Rubio Monocoat Accelerator - component B
UFI: YM00-P0D6-F006-F5MW
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Prevent formation of dust.
Store in cool, dry conditions in well sealed receptacles.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see section 7.
Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. After use of gloves apply skin-cleaning agents and skin cosmetics. Material of gloves: e.g. Nitrile rubber, NBR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed. For the permanent contact gloves made of the following materials are suitable: Butyl rubber with 0.7 mm layer thickness or nitrile rubber with 0.4 mm layer thickness, (recommended: Protection index 6, corresponding to over 480 minutes permeation time according to EN 374). Attention. Due to the special conditions at the workplace (mechanical load, temperature), the daily service life of a chemical protective glove may be considerably shorter than the permeation time determined according to EN 374.
Tightly sealed goggles
Not necessary in case of intended use. Use suitable respiratory protective device in case of formation of dust.
Protective work clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No dangerous reactions in case of intended use.
No dangerous reactions in case of intended use.
No further relevant information available.
No further relevant information available.
None in case of intended use and storage.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for RÖSLER Keramo-Finish® Compound RSP 506 S?
The signal word is warning.
What is the physical form of RÖSLER Keramo-Finish® Compound RSP 506 S?
RÖSLER Keramo-Finish® Compound RSP 506 S is a solid with light grey color. It has characteristic odor.
What is RÖSLER Keramo-Finish® Compound RSP 506 S used for?
Process auxiliary for surface finishing, Industrial use
What are the hazard statements for RÖSLER Keramo-Finish® Compound RSP 506 S?
This substance has 1 hazard statement:
- H319: Causes serious eye irritation.
What is the melting point of RÖSLER Keramo-Finish® Compound RSP 506 S?
The melting point is Undetermined and the boiling point is Undetermined.