Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- EPO-TEK® H77T Part B
- Product Code
- H77T/B
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Adhesive.
Uses advised against
Use only for intended applications.
Manufacturers & Suppliers
Epoxy Technology, Inc.
manufacturer
14 Fortune Drive, Billerica, MA 01821, USA
(978) 667-3805
http://www.epotek.com
Emergency Contacts
ChemTel
+1 (800) 255-3924
ChemTel
+1 (813) 248-0585
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
GHS08
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Bisphenol A Diglycidyl Ether Resin | 25085-99-8 | 10 - 30% | Yes |
| Reactive Diluent | --- | 5 - 10% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move affected person to fresh air at once. Rinse nose and mouth with water. Get medical attention if any discomfort continues.
Symptoms: Inhalation of dusts during cutting, grinding or sanding of this product may cause irritation of the respiratory tract. Vapors may cause headache, fatigue, dizziness and nausea.
Remove affected person from source of contamination. Remove contaminated clothing. Wash skin thoroughly with soap and water. Get medical attention if any discomfort continues.
Symptoms: Causes skin irritation. May cause sensitisation by skin contact.
Remove affected person from source of contamination. Remove any contact lenses and open eyelids wide apart. Continue to rinse for at least 15 minutes and get medical attention.
Symptoms: Causes serious eye damage.
Never give anything by mouth to an unconscious person. Do not induce vomiting. Rinse mouth thoroughly with water. Get medical attention if any discomfort continues.
Symptoms: May cause discomfort if swallowed.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Dry chemicals. Foam. Water spray.
Avoid breathing fire gases or vapors. Cool containers exposed to heat with water spray and remove them from the fire area if it can be done without risk.
Firefighter Protection
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Stop leak if possible without risk.
Do not discharge into drains or watercourses or onto the ground. Avoid release to the environment.
Absorb in vermiculite, dry sand or earth and place into containers. Flush contaminated area with plenty of water.
Materials: vermiculite, dry sand or earth
Related Products
Similar products with comparable safety profiles
EPO-TEK® H77 Black Part A
---
EPOFIX RESIN
---
OPL. EPOXY VR EP 22137
---
EPIKOTE™ Resin MGS LR 285
UFI: RYCF-JSKH-2FC4-C1J2
EPIKURE™ Curing Agent MGS LH 286
UFI: WW85-F7SK-FCCM-QSUC
BENVIC ® ER 778CZ/6560
---
HiTEC® 557 Performance Additive
UFI: VEG7-51X2-E60N-U2NV
HiTEC® 60637 Performance Additive
UFI: XAEY-8VJ0-9X6E-T96Q
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Handle all packages and containers carefully to minimize spills. Avoid contact with skin and eyes. Wear protective clothing as described in Section 8 of this safety data sheet.
Store at room temperature. Keep container tightly sealed when not in use.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate general and local exhaust ventilation.
It is recommended that chemical-resistant, impervious gloves are worn.
Wear tight-fitting, chemical splash goggles or face shield.
If ventilation is inadequate, suitable respiratory protection must be worn.
Wear appropriate clothing to prevent any possibility of skin contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal ambient temperatures and when used as recommended.
The following materials may react with the product: Acids. Alkalis. Strong oxidizing agents.
Will not polymerize.
Avoid excessive heat for prolonged periods of time. Avoid heat, flames and other sources of ignition.
Strong alkalis. Strong oxidizing agents. Strong acids.
Thermal decomposition or combustion products may include the following substances: Carbon monoxide (CO). Carbon dioxide (CO2).
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of waste to licensed waste disposal site in accordance with the requirements of the local Waste Disposal Authority.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Not applicable.
- Shipping Name
- Not applicable.
- Transport Class
- No transport warning sign required.
- Packing Group
- Not applicable.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Proprietäre Informationen gemäß den WTO-Übereinkommen über handelsbezogene Aspekte des geistigen Eigentum Rechte (TRIPS), Abschnitt 7, Art geschützt. 39.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for EPO-TEK® H77T Part B?
The signal word is danger.
What is the physical form of EPO-TEK® H77T Part B?
EPO-TEK® H77T Part B is a paste appearing as paste. with grey. color. It has mild. odor.
What is the solubility of EPO-TEK® H77T Part B?
Slightly soluble in water.
What is EPO-TEK® H77T Part B used for?
Adhesive.
What are the hazard statements for EPO-TEK® H77T Part B?
This substance has 3 hazard statements:
- H317: May cause an allergic skin reaction.
- H318: Causes serious eye damage.
- H334: May cause allergy or asthma symptoms or breathing difficulties if inhaled.
What is the melting point of EPO-TEK® H77T Part B?
The melting point is No specific test data are available. and the boiling point is No specific test data are available..