Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- AGITAN® 295
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Defoamers, Anti-foaming agent
Manufacturers & Suppliers
MÜNZING CHEMIE GmbH
manufacturer
Münzingstrasse 2 74232 Abstatt, Germany
+49 7131 987-100
Emergency Contacts
CHEMTREC
+1 703 741 5970
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
hydrocarbons, fatty derivates, hydrophobic silica, emulsifiers
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Distillates(petroleum), hydrotreated heavy naphthenic EC: 265-155-0 | 64742-52-5 | 20 - 50% | Yes |
| Distillates(petroleum), hydrotreated light naphthenic EC: 265-156-6 | 64742-53-6 | 10 - 20% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Do not induce vomiting; call for medical help immediately.
Immediate Medical Attention
call for medical help immediately
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Water with full jet
In case of fire, the following can be released: Carbon monoxide (CO)
Firefighter Protection
Do not inhale explosion gases or combustion gases.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective clothing. Particular danger of slipping on leaked/spilled product.
Do not allow to enter sewers/ surface or ground water.
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep away from heat and direct sunlight. Prevent formation of aerosols.
Store in a cool location. Store in cool, dry conditions in well sealed receptacles.
Protect from heat. Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see section 7.
Only use chemical-protective gloves with CE-labelling of category III. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: Nitrile rubber, NBR. Recommended thickness of the material: 0,4 mm. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: For the mixture of chemicals mentioned below the penetration time has to be at least 480 minutes (Permeation according to EN 16523-1:2015: Level 6). The determined penetration times according to EN 16523-1:2015 are not performed under practical conditions. Therefore a maximum wearing time, which corresponds to 50% of the penetration time, is recommended. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Goggles recommended during refilling
Use suitable respiratory protective device only when aerosol or mist is formed.
Protective work clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for AGITAN® 295?
The signal word is no signal word.
What is the physical form of AGITAN® 295?
AGITAN® 295 is a liquid with light brown color. It has mineral-oil-like odor.
What is AGITAN® 295 used for?
Defoamers, Anti-foaming agent
What is the melting point of AGITAN® 295?
The melting point is It is technically not possible to determine a value. and the boiling point is The value is above the measuring range of the method. Up to 250 °C no boiling point was observed..