Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Technovit Universal Liquid
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Resin for metallographic testing
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
Kulzer GmbH
manufacturer
Leipziger Straße 2, 63450 Hanau (Germany)
+49 (0)6181 9689-2570
Emergency Contacts
Emergency Contact
+49 (0)6132-84463
24-Hour-Number
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of symptoms. Take affected persons into the open air and position comfortably.
Instantly wash with water and soap and rinse thoroughly.
Symptoms: Skin irritation or rash.
Rinse opened eye for several minutes under running water. Then consult doctor. Remove contact lenses, if present and easy to do. Continue rinsing.
Rinse out mouth and then drink plenty of water. In case of persistent symptoms consult doctor.
Immediate Medical Attention
Consult doctor in case of symptoms, if skin irritation or rash occurs, or if symptoms persist.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, extinguishing powder or water jet. Fight larger fire with alcohol-resistant foam.
Water with a full water jet.
Can form explosive gas-air mixtures. Formation of toxic gases is possible during heating or in case of fire.
Firefighter Protection
Wear self-contained breathing apparatus. (EN 133)
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Bring persons out of danger.
for small amounts tissues
Prevent material from reaching sewage system, holes and cellars. Damp down gases/fumes/haze with water spray jet.
Absorb with liquid-binding material (diatomite, universal binders, for small amounts tissues).
Materials: liquid-binding material (diatomite, universal binders, tissues)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep containers tightly sealed. Avoid contact with eyes and skin. Do not breathe vapor / mist / gas.
Keep containers tightly sealed.
Keep ignition sources away - Do not smoke. Protect against electrostatic charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. chemical protection gloves are suitable, which are tested according to EN 374 Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation If skin contact cannot be avoided, protective gloves are recommended to avoid possible sensitization. Check protective gloves prior to each use for their proper condition. Material of gloves The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. NBR: acrylonitrile-butadiene rubber (0,11 mm) Penetration time of glove material The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed. >30 min
eye protection (EN 166)
Use breathing protection in case of insufficient ventilation. Filter A/P2.
Light weight protective clothing
Do not allow to enter the ground/soil. Do not allow to enter drainage system, surface or ground water.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used and stored according to specifications.
No further relevant information available.
No decomposition if used and stored according to specifications.
Strong oxidizers, amine, organic peroxides
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1247
- Shipping Name
- METHYL METHACRYLATE MONOMER, STABILIZED mixture
- Transport Class
- 3
- Packing Group
- II
Warning: Flammable liquids.
Warning: Flammable liquids.
Warning: Flammable liquids.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Technovit Universal Liquid?
The signal word is danger.
What is the physical form of Technovit Universal Liquid?
Technovit Universal Liquid is a fluid with colourless color. It has characteristic odor.
What is Technovit Universal Liquid used for?
Resin for metallographic testing
What are the hazard statements for Technovit Universal Liquid?
This substance has 5 hazard statements:
- H225: Highly flammable liquid and vapour.
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H335: May cause respiratory irritation.
What is the melting point of Technovit Universal Liquid?
The melting point is Not determined and the boiling point is 100.3 °C (80-62-6 methyl methacrylate).