NextSDS Logo
Safety Data Sheet EN

BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS*

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS*
Product Code
597902

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Activation

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelina.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 4
Skin Corr. Cat. 1C
Eye Dam. Cat. 1
Carc. Cat. 1A
STOT SE Cat. 3
Asp. Tox. Cat. 1

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H227 COMBUSTIBLE LIQUID.
H304 MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H336 MAY CAUSE DROWSINESS OR DIZZINESS.
H350 MAY CAUSE CANCER.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P210 Keep away from heat, sparks, open flames, hot surfaces - no smoking.
P261 Avoid breathing mist/vapours.
P264 Wash affected area thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P280 Wear protective gloves, clothing, eye and face protection.
P301 + P310 IF SWALLOWED: Immediately call a physician or poison control center.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P363 Wash contaminated clothing before reuse.
P370 + P378 In case of fire: Use foam, dry chemical or carbon dioxide to extinguish.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Kerosine (petroleum) 8008-20-6 80 - 100% Yes
Benzenesulfonic acid, C10-16-alkyl derivs. 68584-22-5 10 - 30% Yes
Sulfuric acid 7664-93-9 0.1 - 1% Yes

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If symptoms are experienced, remove source of contamination or move victim to fresh air. If not breathing, give artificial respiration. Get immediate medical attention.

Skin contact

Remove contaminated clothing and footwear. For skin contact flush with large amounts of water. If symptoms develop and persist, get medical attention.

Eye contact

In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention.

Ingestion

Get immediate medical attention. DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to a victim who is unconscious or is having convulsions.

Immediate Medical Attention

Get immediate medical attention.

Medical Treatment

Treat symptomatically and supportively.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

If product is heated above its flash point it will release flammable vapors which can burn in the open or be explosive in confined spaces if exposed to ignition source. Mists or sprays may be flammable below the normal flash point. Do not pressurize, cut, heat or weld containers. Empty product containers may contain product residue. Do not reuse empty containers.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Isolate the hazard area and deny entry to unnecessary and unprotected personnel. Prevent further leakage or spillage if safe to do so. Isolate area. Keep unnecessary personnel away.

Environmental

Eliminate all sources of ignition or flammables that may come into contact with a spill of this material. Prevent further leakage or spillage if safe to do so. Contain spill. Ventilate area. Do not allow product to enter sewer or waterways. Isolate area. Keep unnecessary personnel away.

Cleanup methods

Collect spilled material with an inert absorbent such as sand or vermiculite. Place in properly labeled closed container.

Materials: sand or vermiculite

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Provide adequate ventilation. Keep away from heat, spark and flame. Avoid breathing vapors or mists of this product. Do not reuse the empty container. Wash thoroughly after handling. Do not cut or weld on empty drums. Sufficient vapors from residues may be present to cause explosion and serious injury and/or death. Use non-sparking tools when opening or closing containers. Ground and bond all equipment as required (when transferring products).

Storage

Store between 40 °F (4.4 °C) and 100 °F (37.8 °C) Keep the container tightly closed and in a cool, well-ventilated place.

Hygiene

Wash thoroughly after handling.

Fire prevention

Keep away from heat, spark and flame. Do not cut or weld on empty drums. Use non-sparking tools.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Odor Threshold
Not available.
Colour
Brown
Vapor Density
---
Auto Ignition Temperature
Not applicable
Solubility In Water
---
Relative Density
0.82 - 0.84
State Under Standard Conditions
---
Dynamic Viscosity
Not available.
Crystallisation Point
---
Solidification Point
---
Odor
Petroleum
Explosive Limits
---
Ph
Not determined
Form
---
Solubility
Slight Water
Kinematic Viscosity
Not available.
Properties Status
---
Solubility In Fat
---
Physical State Data
liquid
Flammability
Not applicable
Vapor Pressure
Not determined
Voc Content
81 %
Molecular Weight
---
Flash Point
142 °F (61.11 °C)
Evaporation Rate
< 1 (Butyl acetate = 1)
Boiling Point
350 °F (176.7 °C)
Decomposition Temperature
Not available.
Partition Coefficient
Not determined
Lower Explosive Limit
Not applicable
Appearance
---
Bulk Density
---
Freezing Point
---
Relative Evaporation Rate
---
Cloud Point
---
Colour Intensity
---
Softening Point
---
Metal Corrosion
---
Density
---
Melting Point
Not applicable
Upper Explosive Limit
Not applicable
Physical State
Liquid
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials.

Incompatible

This product may react with strong oxidizing agents.

Decomposition

Irritating and/or toxic fumes and gases may be emitted upon the product's decomposition.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
NA 1993
Shipping Name
Combustible liquid, n.o.s. (KEROSENE)
Transport Class
Combustible Liquid
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS*?

The signal word is danger.

What is the physical form of BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS*?

BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS* is a liquid with brown color. It has petroleum odor.

What is the solubility of BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS*?

Slight Water

What is BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS* used for?

Activation

What are the hazard statements for BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS*?

This substance has 5 hazard statements:

  • H227: COMBUSTIBLE LIQUID.
  • H304: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H336: MAY CAUSE DROWSINESS OR DIZZINESS.
  • H350: MAY CAUSE CANCER.

What is the melting point of BONDERITE C-MC 6045 AERO known as TURCO 6045 *MBO 275 GLS*?

The melting point is Not applicable and the boiling point is 350 °F (176.7 °C).