NextSDS Logo
Safety Data Sheet EN

BONDERITE C-SO 4460 AERO known as TURCO 4460

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE C-SO 4460 AERO known as TURCO 4460
Product Code
406022

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Cold Cleaners with Solvents

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 2
Skin Irrit. Cat. 2
Eye Irrit. Cat. 2A
Repr. Cat. 2
STOT SE Cat. 3
STOT RE Cat. 2
Asp. Tox. Cat. 1

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H225 HIGHLY FLAMMABLE LIQUID AND VAPOUR.
H304 MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
H315 CAUSES SKIN IRRITATION.
H319 CAUSES SERIOUS EYE IRRITATION.
H336 MAY CAUSE DROWSINESS OR DIZZINESS.
H361 SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.
H373 MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P210 Keep away from heat, sparks, open flames, hot surfaces - no smoking.
P233 Keep container tightly closed.
P240 Ground and bond container and receiving equipment.
P241 Use explosion-proof equipment.
P242 Use non-sparking tools.
P243 Take action to prevent static discharges.
P260 Do not breathe vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P280 Wear protective gloves, clothing, eye and face protection.
P301 + P310 IF SWALLOWED: Immediately call a physician or poison control center.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P331 Do NOT induce vomiting.
P332 + P313 If skin irritation occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P370 + P378 In case of fire: Use foam, dry chemical or carbon dioxide to extinguish.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P403 + P235 Store in a well-ventilated place. Keep cool.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Toluene 108-88-3 10 - 30% Yes
Ethyl acetate 141-78-6 10 - 30% Yes
Methyl ethyl ketone 78-93-3 10 - 30% Yes
Hydrocarbons, C6-C7, n-alkanes, isoalkanes, cyclics, <5% n-hexane 64742-49-0 10 - 30% Yes
2-Propanol 67-63-0 5 - 10% Yes
Cyclohexane 110-82-7 1 - 5% Yes
n-Hexane 110-54-3 0.1 - 1% Yes
Ethanol 64-17-5 0.1 - 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If inhaled, immediately remove the affected person to fresh air. If symptoms develop and persist, get medical attention. Immediately remove victim to fresh air. If adverse health effects develop seek medical attention.

Skin contact

Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention. Rinse with running water and soap. In case of adverse health effects seek medical advice.

Eye contact

In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention. Immediately flush eyes with soft jet of water or eye rinse solution for at least 5 minutes. If pains remain continue flushing and contact/seek doctor or hospital.

Symptoms: intensive smarting, sensitivity to light, visual disturbance

Ingestion

Get immediate medical attention. Do not induce vomiting. Do not induce vomiting. Immediate medical treatment necessary.

Immediate Medical Attention

Get immediate medical attention. Seek immediate medical attention.

Medical Treatment

Treat symptomatically and supportively.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide. Foam, extinguishing powder, carbon dioxide. Water spray jet

Unsuitable media

High pressure waterjet

Specific hazards

May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses. Formation of toxic gases is possible during heating or in fires.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Wear appropriate protective equipment and clothing during clean-up.

Cleanup methods

Absorb spill with inert material. Shovel material into appropriate container for disposal. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust).

Materials: sand, silica gel, acid binder, universal binder, sawdust

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Avoid breathing vapors or mists of this product. Use only with adequate ventilation. Do not take internally. For industrial use only. Open and handle container with care. Avoid naked flames, sparking and sources of ignition. Avoid skin and eye contact.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Store in sealed original container. Store in a dry place.

Hygiene

Wash thoroughly after handling.

Fire prevention

Avoid naked flames, sparking and sources of ignition.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Odor
Characteristic
Auto Ignition Temperature
Not available.
Metal Corrosion
---
Molecular Weight
---
Crystallisation Point
---
Cloud Point
---
Solubility
Partially soluble Water
Melting Point
Not applicable, Product is a liquid
Explosive Limits
---
Solidification Point
---
Ph
6 - 8
Partition Coefficient
Not available.
State Under Standard Conditions
---
Flash Point
< 0 °C (< 32°F) Flash Point, Pensky-Martens
Lower Explosive Limit
0.5 %
Softening Point
---
Colour Intensity
---
Flammability
Flammable liquid
Colour
Colourless / Colorless, Light yellow
Physical State Data
liquid
Relative Density
Not available.
Decomposition Temperature
Not available.
Vapor Pressure
64 hPa (20 °C (68°F)) < 200 hPa (50 °C (122°F))
Odor Threshold
Not available.
Density
---
Evaporation Rate
Not available.
Relative Evaporation Rate
---
Upper Explosive Limit
13.5 %
Boiling Point
> 77 °C (> 170.6 °F) Supplier method
Vapor Density
---
Properties Status
---
Kinematic Viscosity
0.1 - 0.8 mm2/s
Physical State
clear, liquid
Dynamic Viscosity
Not available.
Solubility In Fat
---
Voc Content
Not available.
Freezing Point
---
Appearance
---
Solubility In Water
---
Bulk Density
---
Form
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. No decomposition if used according to specifications.

Incompatible

This product may react with strong acids or oxidizing agents. Reaction with oxidants.

Decomposition

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen. In case of fire toxic gases can be released. None if used for intended purpose.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1993
Shipping Name
Flammable liquids, n.o.s. (Ethyl acetate, Benzine)
Transport Class
3
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE C-SO 4460 AERO known as TURCO 4460?

The signal word is danger.

What is the physical form of BONDERITE C-SO 4460 AERO known as TURCO 4460?

BONDERITE C-SO 4460 AERO known as TURCO 4460 is a clear, liquid with colourless / colorless, light yellow color. It has characteristic odor.

What is the solubility of BONDERITE C-SO 4460 AERO known as TURCO 4460?

Partially soluble Water

What is BONDERITE C-SO 4460 AERO known as TURCO 4460 used for?

Cold Cleaners with Solvents

What are the hazard statements for BONDERITE C-SO 4460 AERO known as TURCO 4460?

This substance has 7 hazard statements:

  • H225: HIGHLY FLAMMABLE LIQUID AND VAPOUR.
  • H304: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
  • H315: CAUSES SKIN IRRITATION.
  • H319: CAUSES SERIOUS EYE IRRITATION.
  • H336: MAY CAUSE DROWSINESS OR DIZZINESS.
  • H361: SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.
  • H373: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of BONDERITE C-SO 4460 AERO known as TURCO 4460?

The melting point is Not applicable, Product is a liquid and the boiling point is > 77 °C (> 170.6 °F) Supplier method.