NextSDS Logo
Safety Data Sheet EN

BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*
Product Code
597313

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Paint stripping agents

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 4
Acute Tox. Cat. 4
Skin Corr. Cat. 1C
Eye Dam. Cat. 1
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
Muta. Cat. 1B
Carc. Cat. 1A
Repr. Cat. 1B
STOT SE Cat. 3
STOT RE Cat. 2

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H302 + H332 HARMFUL IF SWALLOWED OR IF INHALED.
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H336 MAY CAUSE DROWSINESS OR DIZZINESS.
H340 MAY CAUSE GENETIC DEFECTS.
H350 MAY CAUSE CANCER.
H360 MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
H373 MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF SWALLOWED: Call a POISON CENTER or doctor/ physician if you feel unwell. Rinse mouth.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Methylene chloride 75-09-2 30 - 60% Yes
Phenol 108-95-2 10 - 30% Yes
Sodium hydroxide 1310-73-2 1 - 5% Yes
Sodium chromate 7775-11-3 0.1 - 1% Yes
Propylene oxide 75-56-9 0.1 - 1% Yes

IDH number: 597313 Product name: BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person immediately to fresh air. Seek medical attention if symptoms develop or persist. If symptoms develop and persist, get medical attention. Administer oxygen or artificial respiration as needed. Do not use mouth-to-mouth method if victim ingested or inhaled the substance.

Skin contact

Remove contaminated clothing and footwear. Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention. Launder contaminated clothing before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Symptoms: chromate scabs and skin ulcers

Eye contact

Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Get immediate medical attention. Eye flushing should continue during transportation to a doctor.

Ingestion

Get immediate medical attention. Do not induce vomiting. If individual is conscious, wash out mouth with water. Provide a glass of water to dilute the material in the stomach.

Immediate Medical Attention

Get immediate medical attention.

Medical Treatment

Methylene chloride is metabolized to carbon monoxide; the resulting elevated carboxymethemoglobin levels reduce the oxygen-carrying capacity of the blood. This product can induce cardiac sensitization to circulating epinephrine-like compounds. Larger exposures may need additional treatment.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Contain spill. Ventilate area. Do not allow product to enter sewer or waterways. Isolate area. Keep unnecessary personnel away.

Cleanup methods

Collect spilled material with an inert absorbent such as sand or vermiculite. Place in properly labeled closed container. Dispose of according to Federal, State and local governmental regulations.

Materials: inert absorbent such as sand or vermiculite

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Avoid breathing vapors or mists of this product. Use only with adequate ventilation. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material. Do not take internally. For industrial use only.

Storage

Store between 40 °F (4.4 °C) and 90 °F (32.2 °C). Keep the container tightly closed and in a cool, well-ventilated place. Open bung slowly to relieve any internal pressure.

Hygiene

Wash thoroughly after handling. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
---
Colour
Pink
Colour Intensity
---
Form
---
Odor
Acrid
Odor Threshold
Not available.
Ph
10.8 - 11.2
Melting Point
Not determined
Boiling Point
105 °F (40.6 °C)
Flash Point
Not applicable
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
< 1 (Butyl acetate = 1)
Vapor Pressure
95 mm hg
Vapor Density
---
Relative Density
1.15 - 1.18
Bulk Density
---
Density
---
Flammability
Not applicable
Upper Explosive Limit
Not available.
Lower Explosive Limit
Not available.
Explosive Limits
---
Auto Ignition Temperature
Not determined
Decomposition Temperature
Not available.
Solubility
Appreciable Water
Partition Coefficient
Not determined
Solubility In Water
---
Solubility In Fat
---
Molecular Weight
---
Voc Content
206 g/l
Metal Corrosion
---
Dynamic Viscosity
Not available.
Kinematic Viscosity
Not available.
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

Not available.

Hazardous reactions

Will not occur.

Avoid

Keep away from heat, ignition sources and incompatible materials.

Incompatible

This product may react with strong reducing agents. Keep away from organic and combustible materials. Strong bases. Metals.

Decomposition

Thermal decomposition products are toxic and include hydrogen chloride and phosgene, in lesser amounts.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
2922
Shipping Name
Corrosive liquids, toxic, n.o.s. (Phenol, Dichloromethane)
Transport Class
8 (6.1)
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*?

The signal word is danger.

What is the physical form of BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*?

BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS* is a liquid with pink color. It has acrid odor.

What is the solubility of BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*?

Appreciable Water

What is BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS* used for?

Paint stripping agents

What are the hazard statements for BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*?

This substance has 9 hazard statements:

  • H302 + H332: HARMFUL IF SWALLOWED OR IF INHALED.
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H336: MAY CAUSE DROWSINESS OR DIZZINESS.
  • H340: MAY CAUSE GENETIC DEFECTS.
  • H350: MAY CAUSE CANCER.
  • H360: MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
  • H373: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of BONDERITE S-ST 5351 THIN AERO known as TURCO 5351 THIN *MBO 275GLS*?

The melting point is Not determined and the boiling point is 105 °F (40.6 °C).